Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I'm writing the f/w upgrade function.
The device is NRF51822, and I use nRF51 SDK_v5.1.0.36092 with s110_nrf51822_6.0.0_softdevice.hex.
I refereed to the example...
I want to measure the time between some different events in my application (using SoftDevice S110).
My idea is, to collect some timestamps and calculate the elapsed duration...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hi, I setup my attibute as 20B array. I'd like to change default data type in Presentation Format descriptor because the default value that is reported to me by BLE Scanner...
Hello,
I am curious to know what is the interpretation for the advertisement data
Advertising Data: 0201050709506562626c6503190002
This advertisement data seems to...
Hi,
Our custom board stops working after updating the connection parameters. We have a nrf51822 chipset custom board with proximity application flashed on it. Device get...
Dear Sir,
I open the Master Control Panel log.txt file, I can see
Serial port read: 04-3E-13-01-00-00-00-00 and
Serial port write: 02-00-00-09
Where can find the full...
I am using a nRF51822 at 16 MHz
What is the math formula behind the BAUDRATE register?
What is the timing error for each of the standard baud rate setting? This is not...
hello,
i was trying to run the sample examples, i tried blinky example from C:\Keil_v5\ARM\Device\Nordic\nrf51822\Board\pca10001 folder. i was succesfull in getting the...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Dear nodic engineer:
i want test environment temperature with NRF51822 inner temperature module.
any information for reference?
any temp graph?
if need calibration?...
Hi,
I have an evaluation kit and I have custom boards that has nRF51822 chip on them.
I am trying to update the firmware(Application) of the custom boards from evaluation...
