Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hello, I am reaching out to you because I am trying to implement a DFU OTA in my project in order to be able to update my firmware with Bluetooth. I have been spending some...
Hello,
I have followed the steps here: https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/installation.html to install toolchains and SDK on a fresh Ubuntu 22.04 computer...
Hello everyone, I'm learning about MCUboot. Currently I have tried searching for information online but still don't have an overview. So I hope everyone shares their experiences...
I built blinky which just blinks a light, pretty simple :). Then I found Anroid nRF blinky in your git hub repo, that's a git hub project that remotely blinks a light. But...
In which subsequent process is the random_static_addr_cfg function reflected? Does the ID change with each build? If the ID changes, will it affect Bluetooth connections?
Due to project requirements, I have made significant modifications to MCUBOOT, but currently all projects use the same MCUBOOT file. Is it possible to have MCUBOOT configure...
I'm going to build an project with 2 AS5600 sensors, and also using I2C mux(TCA9548A) to communicate with 2 sensors.
I have some problem with devicetree. There are two errors...
Hi!
I used SDK15 (may be 15.3) with s132_nrf52_6.0.0_softdevice
I used nRF52832 in two modes in one time.
When I stay in connect with my peripherial to a central device...
Hello,
I have a custom board with a nRF5340 on it. The firmware gets built with MCUBoot in serial recovery mode to update the application core. The serial recovery mode...
Hello. I'm using serial lte modem as mqtt client.
After a while I receive fault. Adding logs:
#XMQTTEVT: 9,0 ESP:LTE: PINGRESP packet #XMQTTEVT: 9,0 PINGRESP packet CR...
Hi, I read somewhere that the LOG module works differently from printk() and uses a separate thread or so. But I couldn't find any information which priority this thread uses...
Hi there,
I am currently having issues flashing an nrf52840 DK on windows 11 using either west for a Zephyr project or nrfjprog. I have successfully done this on a work...
Hello,
I am designing a custom PCB using an nRF5340 and am unsure what my options are for how to program it.
I've seen a number of forum posts saying that you can program...
I've been working for a year now programming nRF5340 DKs using nrfjprog and I still can't seem to figure out what is the right way to program them. It is also very random...
