Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
I am using the Nordic Thingy:53 and trying to collect sensor data using Edge Impulse.
I was able to successfully connect the Thingy:53 to Edge Impulse and stream...
The device i am currently developing is a battery powered dongle with internal power supply unit for battery charging. I am using nrf5340 USB pins D+ and D- for communication...
HI, i have been using the nrf9151 to download my OTA's it has been working fine, but since this week it stopped working for all device we have deployed, i suspect it is related...
Hi ... have code that outputs I2S in master mode. The slave, a NAU8822 device requires Master Clock Source between 8 and 33MHz.
The 54L MCLK pin is duplicating the BCLK...
Hi,
I have a fresh clone of Zephyr version v3.4.0-rc1-66-g462dc9746b42. I want to build and debug the unmodified project samples/tfm_integration/tfm_secure_partition.
...
Hi
I want to add the nordic documentation as an MCP server to claude and gemini clis. But this seems to require authentification by Kaipa, which is a paid service ?
...
Hey Team,
Whenever we flash the audio application (from the official samples provided) on a development board and leave the board unpowered/unattended for 10-15 days, the...
What is the correct way to connect an nPM1304EK (or other nPM product) to an nRF7002DK? Is it possible to do this and power the nRF7002DK via the PMIC but have the USB connected...
When trying to figure out why we couldn't flash the network core on the nRF5340 with pyOCD, we noticed that the Debug Base Address of the AHB_AP returns 0xe00fe002 for the...
I am trying to migrate my project (for a custom nrf5340/nrf7002 board) from NCS2.9.0 to NCS 3.1.1, to hopefully get the wifi WPA Enterprise functionality to work.
This is...
I can connect to targets using the JLink WiFi probe and JLink Commander (JLinkExe), but when running `nrfutil device list`, they don't show up there. Can you please patch...
Hallo together,
I noticed today that the example circuit diagrams for the nRF9160 seem to have been using a completely incorrect tolerance value for the supply capacitors...
Hello.
I am currently testing nRF Cloud and encountering an issue. I encountered a build error when merging the Peripheral Memfault Diagnostic Service (MDS) sample program...
Device: nRF5340
SDK: nRF Connect SDK v2.2.0
IDE: nRF Connect for VS Code v2023.6.345, Running on Windows 10
------------
We are working on a new project for the nRF5340...
System Calls link is: https://docs.nordicsemi.com/bundle/ncs-3.0.0-preview2/page/zephyr/kernel/usermode/syscalls.html --> not found
the "3.0.0-preview2" is likey the cuprit...
