Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hey there! I'm very new to BLE, so I wanted to reach out in this forum to confirm hardware capabilities before I purchase any devices. I'm currently looking at the nRF52840...
hi team,
i am using nrf52840 controller,in my project along with with nrf_sdk.
i wrote a led blicking code using ble protocal on segger IDE 5.40 and i want to see data...
Hi, I'm using nRF52840 in my project. I successfully integrated the BLE DFU service and its characteristics in my firmware, Now I can update the firmware through the nrf-connect...
Hi, we are doing mass production using PLT. And we have found that like 10% of the sensors are stuck in certain stage as seen in following power cycle images.
The program...
Hi,
In the product specification document of nRF52840 it says that in order to read the counter register's value I need to set the capture task NRF_TIMER1->TASKS_CAPTURE...
Hello,
I would like to use the UICR customer registers to store our devices serial numbers.
Can you please point me to some example code for nRF52833 SoC.
I am using...
Hallo Team,
I would like to operate nrf5340 BLE module (BC40C from Fanstel) in "Normal Voltage Mode". Please find the screenshot of the module below. I hope its clear...
Hi,
Just wondering if it's possible, or there is a reliable way to dynamically change the sampling period of the CAF sensor manager module . Specifically the values defined...
Hi everyone!
I am using ESB with the nRF5340dk without ACK, but from time to time need to send a packet with an ACK request in order to send some commands from the receiver...
Hi,
After successful building of pca10040_s132_ble_debug example with changes to project :
- excluding SEGGER_RTT_Syscalls_SES.c from build
- from flash_placement.xml...
Hi,
We are hoping to send our samples for CE certification. We use nrf52805 IC in our design. We do not use any precertified modules.
Looking at the Direct Test Mode folder...
Hi!
We're working on a development project using nRF52832. Our original prototyping PCBs used the nRF52832-QFAA. On these boards, the nRF worked without issues, and we could...
Hi,
I have builded a circuit with a nRF52DK and a mpu9250 IMU. If I power the Sensor with VDD the Zephyr driver and all of the Software performs well and the values from...
Hi,
I am using nrF52840 with nRF Connect, Visual Code Studio (Zephyr)
Is there any guide or a tutorial with an example that shows how to create a static library on nRF...
