Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Dear Nordic Team,
on my board with NRF85240 High Voltage mode is used. Accordingly to datasheet (5.3.8.2 Regulator Specifications, REG0 stage), in this mode the following...
Can you help with why I get this serial debug message when trying to start Headset nrf5340_Audio DK in DFU mode
HR [00:00:02.068,450] <err> dfu: SMP_SVR Advertising failed...
Hi!
I have an issue with control of the MAGPIO during RFTEST procedures.
The device is using RF Switch (like Thingy91) and I want to perform SNR/Received signal power...
Hello All,
Hoping to hear your opinion as I have little experience on how reliably the following would work.
The device should count pulses or edges from a reed switch...
Hi,
I'm using a Thingy:53 for some prototyping work. The device is configured with the standard USB CDC ACM as logging backend and I use pyserial-miniterm to access the...
Hello All,
I hope all is well. I have now been using Nordic ICs for close to 10 years and have become familiar with SDK5 and developed multiple applications using it....
Hello,
I would like to fast adc some analog signal from my opamp PCB. I am using nrf5340DK SDK1.9.1 with VS Code.
Got the example code nrfx_saadc.zip from and my first...
Hi,
I'm using the following function in my project, in order to get an idea of how much memory can be reserved with malloc :
This function should return the last value...
Hello,
I have a question about the Kconfig extension for VSCode.
When I use the nrf52840 DK, the Board Selection correctly check the nrf52840dk_nrf52840 and all the configs...
I've been continuing to work on why my power level seemed low after getting the Skyworks FEM in my Fanstel BT840x module going, per this thread:
So far, I've been setting...
I want to increase the rate of data from UARTE to RF FIFO.Can data be transferred from the cache to the RF FIFO using DMA?
nrf52832 nRF5_SDK_17.1.0_ddde560 S132
Hello, I am trying to understand the adc example using the PCA10056.
HI can see the following code that initializes 3 `zephyr_user` channels
In the DT file,...
Hi,
I recently went through the manual installation instructions for the nRF Connect SDK posted here ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_installing...
Dear,
I would like to remove the DCDC converter in between the li-ion cell which is supplying the system and the system.
The idea is to use our micro battery as the...
