Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
I'd like to use a Python script to update the modem firmware (full update) instead of the Nordic Programmer tool. The purpose is to have this ability on the manufacturing...
I have a nRF52840 Dongle. When I connected it for the first time to the Bluetooth Low Energy app of nRF Connect for Desktop, it loaded automatically the firmware. My question...
Is there a way to read the mac address from the serial tty of an nRF52840? I have multiple dongles programmed with the BLE sniffer (nrf_sniffer_for_bluetooth_le_4.1.0) and...
Hi,
I was using the nrfx_saadc_buffer_convert to make everytime a single sample.
Now I did find out there is also nrfx_saadc_sample_convert. How do I initialize this...
I've been trying to debug a recurring hard fault around nrf_log_frontend_dequeue. This occurs sporadically (between 10-60min) into testing my firmware. When the fault occurs...
Hi all,
normally our system runs in low power mode. When triggering the SAADC the first samples (using oneshot mode) will be off (slightly too low).
I can work around...
Hi,
I need to create run time count that increases every 0.065536sec.
I found a way doing so by using HFCLK without any interrupts.
My questions are:
1) Are there...
Hi, I am working on the nrf52840 dongle using the softdevice.
I would like to know whether it is possible to add OTA DFU capability to the default open bootloader that allows...
Im quite new to development with the DK so bare with me.
Currently I am able to read digital values (0 and 1) from the potentiometer using pin P0.03.
I am using the function...
I had toolchain manager 0.10.3 and a project using NCS 1.91. Unfortenuately I have updated the Toolchain manager to 1.0.0 and now my project does no longer show up and the...
I have a NRF52840 based custom device that I can program just fine with a NRF52840-DK.
However, when I try to use a NRF52833-DK I can erase and flash the softdevice just...
Hi,
I work with nRF52840 DKs and I am working for indoor positioning system based on RSSI signal strength. I want the RSSI signal strength to be sensed and transmitted to...
Hi Devzone team,
My customer wants to design the LTE-M antenna for their tracker project in US market, do we have any antenna reference or design guideline? I see we have...
Hi,
I am looking for a BLE module that I can program to send a Thyrmistor signal 250 meters or more. The BLE module has to be small and able to collect A/D Convertor and...
Hi ,
I am trying to get GNSS on thingy 91 to work. It seems like I have the same issue as this thread:
I cannot get a fix. Currently, I am using the 1.3.2 firmware ( the...
