Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
After switching to the BLE advertising module in SDK 16.0.0 (on an nRF52 board) and using it for over 3 months I am now discovering that no matter how I configure the advertising...
My firmware is blocked on custom board until RTT connects: Code hits and blocks on a printf. This doesnt happen when using an NRF5340, but does with NRF5280. Just trying to...
Hello, I am using v3.1.0 of the nRF SDK with a nRF52840-DK board.
I would like to run the "Counter RTC Driver Sample" (nrf/samples/zephyr/drivers/counter/alarm). The README...
I am updating our production tools and starting by simply trying to program the Thingy91 (or DK) with the following example from the internet. I keep getting timeout errors...
Hi Team,
I have configured I2C0 for reading data and sending iqs323 and iqs7211a. i have configured overlay file according pin conjuration which is below.
Pin configuration...
HI
Currently using NRF54L15 with NCS v3.0.0 and the periodic_sync_conn sample. I have created sysbuild.conf and added SB_CONFIG_BOOTLOADER_MCUBOOT=y. After compilation,...
Hi all,
I’m working with an nRF-based board and need to via software disable the internal DC-DC converter and use the LDO exclusively for testing purposes. I’m unclear on...
To confirm, when connecting a power source to VBAT for the first time, nPM2100 will automatically transition to Active mode assuming the power source can deliver enough current...
The error started coming after updating the sdk version from ncs v.2.9 to ncs v3.1
[00:06:58.439,514] <inf> _https: Log:Sock before -1 [00:06:58.484,649] <inf>_https:...
Hello,
Going through DevAcademy SDK Intermediate and it mentions running 'west boards'. Doesn't work for me:
Any ideas ?
Sadly after weeks of little problems like this...
Below is my change, set options to BT_LE_PER_ADV_OPT_USE_TX_POWER
But it always display Failed to set periodic advertising parameters (err -5) , why?
My hardware is...
Hi again,
I'm having trouble with the Matter Test Harness. I have been running tests in isolation one by one and fixing issues the TH finds. Now I have run into an issue...
Hi,
toolchain:-v3.1.0,sdk:v3.1.0. i am using the vscode software for the development
Basically i am trying to connect the peripheral using the address (mac:- 7C:D9:F4...
Hello,
I am using NRF5340-DK for my project and I wanted to know if there is some example on how to read and extract the public key from this type of certificate. I have...
