Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I am trying to implement bonding in central BLE uart_app example code but I don't know how to proceed as I'm a beginner . Do we need to make any changes at peripheral side...
Hello Nordic team!
I'm following this tutorial from Nordic to do DFU OTA: https://devzone.nordicsemi.com/guides/short-range-guides/b/software-development-kit/posts/getting...
I am following this post regarding reading the static MAC address for the nRF52840: https://devzone.nordicsemi.com/f/nordic-q-a/68376/trying-to-extract-the-static-mac-address...
Hi, we have a device that reads two sensors on separate i2c buses consecutively and transmits these using ble_nus_data_send().
The i2c sensors are read on an interrupt timer...
Hello all,
I am moving from the Arduino Uno to the nRF52 DK on Segger. A big difference
When looking at the examples, I cannot see the so-called setup() method, so, I...
Dear Forum,
I have the following issue (my System: Ubuntu 20.04):
I created the secure bootloader with Softdevice S140 (v.7.2.0) for 52833 chipset, I use a 52833 Development...
I have an application based on the peripheral uart sample, using NCS 1.8.0. I need to build in a version string that is queryable, so that anyone who connects to the device...
When i intially burn the code on dk, my dk should be in system off mode ie all functionality should be off. Then i want to press a button for 5 seconds with which the device...
Hi,
I am using the nrf52840-DK with the nRF Connect SDK version 1.8.
I have modified the central_multilink sample to connect to a BLE peripheral which requires a secure...
Hi,
We have a mature product based on the STM32 ARM processor family running the uCOS OS and our development toolchain is IAR. The workflow has worked well in the past when...
Dear all,
I ran LPCOMP example from SDK16 on nRF52 DK and it works just fine.
But I've occurred some problem modifying reference voltage. I init the lpcomp the same...
Hi ,
I have my own custom nrf52832 pcb. I have 2 chips on my pcb.
I program my device with Nrf52 Dk.
When I program MCU 1. The program is uploaded successfully and i...
Hai
I'm using nrf52811 and sdk17.1.
I tried all peripheral examples But I can't set advertising data to more than 31 bytes.
If I increase the data size some parameters...
Hi , I am using ZEPHYR rtos , and using the internal bootloader and its working fine and there are two images but now my code size has increased and i can not store 2 images...
Hi
I want to use app_uart_put() to send an array which is over 4096 bytes.I try to change the value of UART_TX_BUF_SIZE to 10K bytes，then call the app_uart_put() to send...
