Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi,
We want to know more about BLE mesh OTA update in Nordic Connect SDK V1.8
Can you please share detail implementation on Firmware Over the air update in NCS 1.8 ...
Hi,
With the latest SDK v 14.2 is it possible to do OTA updates to nRF52 from OSX/Windows/Linux without the use of additional DK? I understand that for iOS and Android...
This might not be the optimal forum for this question, but I'm not sure where else to post it. I have a (I think) very simple question about configuring Zephyr.
I have a...
Hi!
Currently working on a firmware upgrade of nRF91 ns(non-secure) board and build a smp_svr demo from ncs samples found on ncs\v1.7.0\zephyr\samples\subsys\mgmt\mcumgr...
SDK: NCS 1.7.1.
Based on: Peripheral UART example
Central: nRF Dongle
Peripheral: nRF52832
Hi,
I am running into an issue using the "Just Works" pairing method when...
Hi, I was wondering if there is any way to advertise connectable, but non-scannable advertisements.
My device does not have a scan response, but I still see a lot of scan...
Hello,
There is a small problem that I don't know how to solve. I tried looking for it but to no avail. Essentially, my device which runs on NCS v1.7.0 will stop advertising...
Hello,
I am currently trying to record audio using a PDM microphone on the nrf52840 using the nordic PDM library. I have configured the PDM with the default settings, enabled...
nRF52810 SDKs and SoftDevices compatibility matrix does not list nRF52810 SoC revision 2 in the list of compatible SoC revisions for nRF5 SDK. Revision 2 is listed only in...
Hi
I have a machine MacBook Pro 14 Inch 2021
Chip : Apple M1 Pro
I am using nrf52840DK
Using Segger 5.68. installed via Toolchain
Using sdk connect 1.8
The J-Link...
Hello,
We have a head-scratching issue For the sake of brevity, please assume in the following that the definition of "it works" is "the bootloader manages to jump into...
Hi,
I'm trying to interface Adafruit 9-DOF Absolute Orientation IMU Fusion Breakout - BNO055 sensor with nRF5340 DK board. Can you please help with the code where I want...
Hi,
I installed NRF connect SDK,
after installation I navigate from NRF connect desktop app -> Toolchain Manager
V1.71 is installed in D:\Nordic_App\Nordic_SDK\nCS...
I'm using VS 1.7.1 on Windows 10, with the nrf9160dk_nrf9160_ns
Playing around with myFirstApp from the VS Youtube Tutorials, I wanted to redirect output to uart2 and map...
I followed the getting started guide for Ubuntu:
https://docs.zephyrproject.org/latest/getting_started/index.html
I can build Blinky, but when building my project I get...
