Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi,
We are currently looking into using the nrf9160 for a smart meter gateway like solution. It is of particular interest to us to know if we would be able to achieve compliance...
Hi all,
I am having issues with the nRF connect programmer that is used to flash the mcu.
I have installed the software my nRF connect version is v 3.10.0 (It is not available...
I installed nRF Connect and inside it I installed Programmer. When opening the programmer I get the following exception:
And system report:
I already tried following...
Hi,
I currently have a working project with BG96, embed TLS and LWM2M.
I'm investigating some problems that occur when the connectivity is interrupted during TLS handshake...
Hi !
In nRF9160, want to implement nrf_mode_lib for modem. Therefore, need to select non-secure(ns) board.But want to set UARTE2 as secure. As UARTE2 provides communication...
Hello!
I am completely new to development with the nRF52DK.
Today I spent the entire day trying to set up the IDE and enviroment to make my first application, but that...
Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello All,
I am using the BE33 (nRF52833 based) module of the Celium Device. I am able to flash the code by using SWDIO and SWDCLK pins. Also, I have tested the BLE advertisement...
Hi,
I am running into this issue when receiving over uart where the byte received is always one byte behind relative to the byte sent by the sender. The byte received is...
I've never been able to get >= 10.13.0 of the nrf tools working. The previous versions work fine on my x86 mac, but there are a series of problems with the newer tools. First...
Hello,
Is there a way to configure mcuboot to allow updates to the bootloader itself? That feature is supported in Nordic's bootloader, but I haven't been able to find...
Hi All,
We are using NCS v1.7.1 on our custom designed nRF52840 board. We have a touch screen interfaced with I2C to our device. There is one more controller connected on...
I am making a "program that keeps multiple software in Flash ROM and reads arbitrary software according to instructions".
When I open the hex file with a text editor, the...
So i have my nRF5340 DK and have been pretty successful in getting my Mesh working with some Thingy:52 devices, some Adafruit Feather devices and some Sengled Lamps.
Groovy...
I am trying to read from the LIS3MDL sensor using spim on the nrf52840 dongle. I gave the rx buffer with the length of 7bytes. Whenever i tried to read from the sensor, I...
