Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am experiencing system resets caused by the WDT (Watchdog Timer) while using the nrf52832。
This is my WDT configuration code：
void system_wdt_init(void) { uint32_t err_code...
my sdkconfig.h related to fds
my entire code error: my entire sdkconfig
i have tried changing no of pages , using nvmc driver, but i am getting the same error steps...
HI，
I am using the nRF54L15 with SDK v3.0.0. I am currently using Timer20 for a counting function. My original power consumption was 4.6 μA when Timer20 was not enabled...
Dear Nordic DevZone,
I have a question which is quite noobish but I want to make sure I am using the right tools for the job. My setup looks like this I have a raspberry...
After gradually increasing up to ncs 3.1.0, the following issue occured: After:
LOG_INF ( "Initializing modem library" );
err = nrf_modem_lib_init ();
if ( err ) ...
Hi,
I’m working on the T5838 Invensense PDM driver for the nRF54L15 .
I’m referencing this driver: IRNAS T5838 Driver , and have updated it to work for SDK 3.0.2 (including...
Hi [Nordic Support Team / Developer Team],
I would like to confirm why the nRF54L15DK is not listed among the supported development kits for the Bluetooth: Peripheral ANCS...
I tried two different applications in BT fundamentals, the solution to Lesson 3, Exercise 1 and the solution to Lesson 4, Exercise 1. Both show "Advertising successfully started...
I'm using zephyr with a custom board (nrf52840) which has a ssd1306 OLED. I have it configured to use i2c0 and is working fine with lvgl.
When I try to enable uart0 (using...
After a recent update, I'm frequently finding the VS Code UI unresponsive due to intelliscan re-indexing.
About my setup. I have a complex environment with 4 different...
Hi Everyone,
I have designed the NRF52832 PCB, Before I order the PCB I hope you guys can review it one time.
Can you please review it, Also I want to tune the antenna...
Does the RISC-V processor of this SoC have access to all the peripherals similar to Cortex-M processor? Can it be used for edge AI using Neuton or ML studio ?
Hi everyone, I have made a custom app by merging together code from nrf5340_audio and iso_acceptor code. I have one issue however - audio_sync_timer_capture seems to return...
Hello, I have discovered that Zephyr's fuzzing sample: https://docs.zephyrproject.org/latest/samples/subsys/debug/fuzz/README.html is not working with NCS v3.0.2. Reproduction...
Seeking help with using SystemView on a custom board with an nRF9151. My code is based on the Azure IoT Hub example. I can enable CONFIG_TRACING =y and CONFIG_SEGGER_SYSTEMVIEW...
