Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
Does nrf9160 support C++? If it does, which version? I saw a similar question over 2 years ago in which C++ was not recommended ( https://devzone.nordicsemi.com/f...
SDK: v17
Softdevice: S112
I am currently checking the throughput using nrf52810 or nrf52805.
In device A, data is input as Uart and checked as device B input data...
Hello everyone! I want to evaluate the exact power consumption from the camera (Arducam Mini 2MP OV2640) using the nRF52840-DK as well as its SDK with the nrf52-ble-image...
Hi,
I am trying to implement USB DFU on a NRF52833 with nRF5 SDK for Thread and Zigbee v4.1.0 and nRF5 SDK v16.0.0.
In a first step I want to perform this on the devkit...
Hello,
I have several issues with the new nRF Connect for VS Code SDK, I put them into one ticket, although, some of the issues could be related directly to nRF Connect...
Hi
1: According to this ticket: https://devzone.nordicsemi.com/f/nordic-q-a/28335/nrf52840-usb-pins-impedance you recommend to not
have any serial resistors on the D...
Hello!
I have installed Android nRF Mesh application version 3.0.3.
Also I bought Yeelight YLDP10YL lamp which is qualified mesh product ( https://www.bluetooth.com/learn...
Hello,
I am getting a bit lost in the pool of different versions and libraries. For simplicity, I just want to achieve a single goal to start which is send a bluetooth packet...
Hi
1、 I want to know the connection mechanism of one Central connects multi Peripheral.
2、What is the time interval between one connection switching to another? Is there...
Hi Guys,
i am using nordic nrf52840 controller. and i have my own bootloader application code.
and once the controller boot up then it start mbr code from 0x00000000...
Dear Nordic Team,
Is it possible to have dual role (one at a time) on nrf52805? Is any such stack available?
I am very new to BLE and i am facing a problem in BLE Uart...
Hello Everyone,
I am a beginner for working on Nordic devices. I have one query. I have to build a firmware in NRF52840. Now 2 different apps will be connecting to this...
Hello
I am using 5 nrf52833 dev kits and the ble_zigbee_dynamic_light_bulb_eddystone example from nRF5_SDK_for_Thread_and_Zigbee_v4.1.0
I have modified the following...
I'm trying to achieve a low power operation on a device which has a nRF52833 module with a SPI peripheral on Zephyr. It is based on the peripheral_lbs.
The intended behaviour...
