Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
I need an example of Timer and ADC for nrf5340. Already I checked this example but it is unclear and also has some error with semaphore. could you please give me...
Hi
Currently we were looking for buying Laird 451-00004 dongle to be used with PTS software. Since the device is not available with any of the distributor. we are approaching...
chip:nrf52840
SD:S140 6.1.0
SDK:nRF5 SDK v15.2.0
ASSERTION FAILED often appears in my firmware, connecting J-link in debugging state or turning on NRF_LOG and outputting...
Hello, I am using FDS to store three int32_t numbers. Here is my code for storing :
Here is my code for reading :
Here are the logs (stored values are the correct...
I'm having trouble sending more than 256 bytes over TWI.
nRF52840 SDK17.0.2
Used Function :
I have to send 8,208 Bytes continuously through the TWI interface in the...
Hello,
I'm trying to establish a connection with my own MQTT brocker on MQTT Box. I change the config on the prj.conf and on Kconfig file, like this :
But when i rebuild...
I downloaded the CIAA Layout and BOM resources from this page: (1.0) https://www.nordicsemi.com/Products/Low-power-short-range-wireless/nRF52832/Download#infotabs . I opened...
Hello there,
I cannot manage to activate my SIM card. Can I get some help?
* Tried outside of my company firewall? Yes, to no avail.
* Tried entering only the first...
When NRF52832 as SPI Slave, how can I know how many bytes the slave should read,the API nrf_drv_spis_buffers_set(&spis, m_tx_buf, length, m_rx_buf, length)),does not have...
Hi guys,
I am now facing a problem that I can't stop the pwm by using nrf_drv_pwm_stop.
Here's my initial code for pwm and start the pwm in the while loop.
The output...
Hello, I've tested multiple NB-IoT cards from China Mobile using the asset tracker on nRF9160 DK. The NB on Band 8 ( AT%XCBAND returns %XCBAND: 8) has no issue connecting...
I first assumed the obvious that the first library would be used with the (Visual studio) multi-threaded DLL/MD option and the second would be used with the multi-threaded...
Hi,
Currently we're developing RGB bulb which has mesh feature (nRF52832). So this done by using nRF5 SDK 15.2.0 and Mesh SDK 3.0.
We're able to control all three channels...
Hi Team
I would like to store a simple integer value in flash and read it back after a power cycle. I already studied the library Flash-manager of the nRF5 SDK for Mesh...
