Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello, can you please provide more information and instructions on how we configure the input capture on nrf52840 dev board using zephyr? All sample examples only cover pwm...
Hi,
Recently, we have ordered PCBAs using nrf52832 to online PCB manufacturers.
During a test, we found that some boards can use OTA firmware update, but some are not...
Respected Sir/Ma'am,
I have attached my schematic below.
I need to perform Offset calibration operation for which I need to control the SCLK value.
I am sending...
board : nRF9160DK
SDK : nrf connect SDK v1.5.0
sample : \v1.5.0\nrf\samples\nrf9160\lwm2m_client
Hi, i am testing lwm2m_client example and
Q1. i dont know how...
I'm trying to implement an immutable bootloader + MCUBoot + (SPM and APP), and then update the app via fota.
My implementation is based on the asset_tracker_v2 example....
Hi,
I'm working on an app where I need to collect data from a sensor, and send it over NUS every 10ms.
I'm using nRF5340-DK (0.11.0), and I'm using nRF Connect SDK v1...
Hi,
I need help to clarify the API for IAS zone server. If I can get example implementation, it would be great.
I have hard time understanding how zb_ias_zone_app_callback_t...
Hi,
I am new to nRF9160DK . I want to set RTC time for the nRF9160DK.
In the application we are getting UTC time from NTP server and we need to set RTC .
I have referred...
Hello,
I am trying to get my nRF9160 to connect to a https server via AT commands, but this is as far as I've been able to get.
In the end this will be used in a project...
Custom board, ncs v1.5.0, modem FW v1.2.3, SES v5.34a. The code is based on the Asset Tracker (v1), LTE with PSM, motion-activated GPS, using MQTT to send messages to a private...
Hi guys, I'm struggling on multiple fronts to make the system building up again after NCS upgrade to 1.5.0. This is the last uncanny warning I get at build time. Please give...
Using SD S140 7.2.0 SDK 17 (nRF52840).
I cannot write to internal flash addresses above 0x78000.
I am calling nrf_fstorage_init setting start_addr=0x68000 and end_addr...
Hello,
I am looking at the TX start-up current for the nRF5340 mentioned here (last 2 entries in the Radio current consumption (Transmitter) table) in the product specification...
Hello,
I am having an issue where I am trying to send a payload in the ACK in the ESB protocol. The issue is when the PRX gets a payload it was not expecting (i.e anything...
Hi Nordic team,
Please guide to resolve the error .
While trying to convert the model_handler.c to model_handler.cpp the below deceleration shows multiple compilation...
