Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
I wanna try to connect multiple device with only one Android, but I don't know how many devices Ble can connect to only one Android. When I try demo on Samsung galaxy S8,...
Hi,
I have an issue that is urgent for me, as we wish to add DFU capabilities via pre and post production hardware. I am using Android 10 on Samsung Galaxy A10 to test...
Hi,
I was able to create a device driver support for a DAC, model TI DAC80501Z. In the first place I put the driver in zephyr/drivers/sensors.
I works fine.
Then I made...
Hi Team,
Please provide the nRF52 based module Characterization, software testing for FCC/IC/ETSI certification test procedure and document
Is DTM test enough for FCC...
According to SDK documentation for GFX library :
“After generating a font, you must change FONT_INFO::height to be described in bits (pixels), not pages”
But in the provided...
Hi,
I can build the blinky_pca10040_s132 example and I loaded it in the nrf52840-DK without errors but nothing happens in the bord I can´t see any lead blinky.
Please...
Hi
We are sending devices for RF/wireless testing and need test firmware that allows for the Bluetooth frequency and transmission power to be easily adjusted. Does Nordic...
Hi.
As you have made a progress in your development of both hardware and software. It would be greate if you remove old videos from youtube. I have just spent some time...
Hello.
I am using nrf52832 and Segeer Embedded Studio.
I want to add a timer function to the ble_app_uart example so that the sensor value is read every 50 ms.
So I...
I am trying to build nRF5_SDK_17.0.0_9d13099\examples\ble_peripheral\ble_app_uart for the PCA10100 DK.
I am using DFP 8.32.1.
I get the following warnings:
RTE\Device...
Hello
I am wondering if there is example where dfu is implemented within application and bootloader is only coping image from flash bank to application space. My companys...
Hello all!
I'm finding a lot of what I'm able to do with the nRF52840 mostly straight forward, especially with the wealth of examples included with the SDK. I'm currently...
Hi!
I'm using nrf sdk v1.3.0, for power saving, i'm have to activate and deactivate lte, after a few time activate, send http request, get data and deactivate lte, the modem...
I am working on design of low power BLE sensor based on nRF52. Sensor data is included within advertising packets, in manufacturers data field. I would like to detect event...
