Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi,
I want to send multiple packets on a notify characteristic using ble_blanky app as baseline but only first 4 consecutive notifications are received on android side....
I would like to set the UUID below, so please tell me how to set it. 　1)base UUID: 　2)Service UUID： 　3)Status Characteristics UUID： 　4)Control Characteristics UUID： 　5)Blood...
Hi,
I am using
nRF52840
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
I set tx power in advertising as below.
sd_ble_gap_tx_power_set...
Hi,
We are developing a product that consists of a "central" and "peripheral" device. A small amount of data is periodically send from the central to peripheral device...
Hi. We are using nRF52832 and we have problem with UARTE. SoftDevice version - S132 5.0.0, SDK version - 14.2.0. Our application uses nRF and Mbed Serial to communicate with...
I have created my own custom project based on the template ble app, porting over the relevant includes and settings in order to start fresh. Despite my section placement file...
Hello,
I'm using a development board PCA10040 with sdk 16.0 I'm trying to organize a data streaming between two devices. Nrf52 board collect data (27 bytes with interval...
I bought dev board for evaluation purpose (currently run on ESP32)
chip: nrf52832 board: E104-BT5032A-TB ( http://www.ebyte.com/en/product-view-news.aspx?id=956) framework...
Hello Nordic! Im making a custom Nrf5232 QFAA, and for the antenna, I want to use only a grounded micro-coax connector and not a trace antenna, is this even possible? I've...
1. I want to use the following command line to compile the nrf9160 project, but the error.
2. Can you help me find the cause of this error?
3. Please provide me with...
Hello, I encounter a problem when I am trying to measure the current consumption of the nRF52840 on the nRF52840-DK. I have set the board in direct supply mode as described...
Hi,
I'm using a nrf52832 based beacon with some sensors attached. To retrive the current time I use the CTS client. Actually, I'm following the ble_app_cts_c example to...
Hi all,
this is a already known error, and most answers to it is use Segger Embedded Studio or buy the license or so whatever.
But i wanna know how can i manage the size...
Hallo,
i am interested for the nRF52833 and also for the corresponding Development kit which supports Bluetooth 5.1 and direction finding AoA&AoD for positioning. The questions...
