Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am currently testing Optiga Trust X using an NRF52 DK. I am using armgcc as my toolchain.
The example provided by the nRF5 SDK v17.0.0 is a great starting point and I...
Hi,
I am using nrf52810 and a sample SAADC code from the examples folder provided by the manufacturer. I have connected a potentiometer for validating my output values....
A continuation from here: https://devzone.nordicsemi.com/f/nordic-q-a/64842/mesh-pa-lna-problems
If I want to only enable the PA/LNA chip for the mesh stack, but not for...
Dear Nordic Support,
Our product is based on nrf52840/s140 and we have difficulties connecting to it using Huawei P8 Lite while it is fine using other Android or iOS phones...
I have a compiled code and I want only to change the uart pins without compiling the code again
If it is possible to modify only the hex code, how can I find the UART pins...
I am trying to find where to submit bugs against the pc-ble-driver. There are two major bugs I have found
saved CCCDs (in a bonded connection) do not get restored when...
Hello, everyone
I use NRF52840 to configure TWI to operate the sensor, but I don’t understand it.
Can the hardware TWI of 52840 be mapped to any IO?
Or is there a fixed...
Hello!
NRF52832 is used as a central for connecting with phones as peripheral. NUS service is used. Lesc is used too.
SDK 17 SoftDevice S132 V7.0.1
On android phones...
when I use usb to transfer, i fine many datas are lost.Is it because the DMA size is too small?Where can i see the dma size?(In nrf52833/examples/peripheral/usb_cdc_acm )...
I am trying to connect a SPI device to the external connector pins on the nRF9160dk board. I believe I know the name of the SPI device and the pin connections from the device...
Hello
I'm trying to print out several sounds with one buzzer. To do that, I need to be able to change the frequency.
PWM was initialized and reset using code. An attempt...
OS: Linux Ubuntu 18.04
Compiler: Gnu ARM embedded
HW: 2 nrf52840dk boards
NRF SDK: 16.0.0
I am trying to send data using L2CAP CoC. I have looked at the ots example...
Hello,
I am trying to get familiar with the DeviceTree macros and started experimenting ...
So, in the light controller example main.c I replaced this macro
#define...
Hi Nordic,
I bought an nRF9160 DK for use in the UK on o2's network, but the signal in my home office is poor resulting in me having to go to the window to get connectivity...
