Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Should the toplevel declaration bool nrfx_power_irq_enabled; in nrfx_power.c have a `static` qualifier? I'm using openocd/gdb to load a GCC-compiled firmware onto a custom...
Hi,
I think I have properly configured my application to authorize reads on characteristic, yet I do not see an event generated. I get write events, but I don't get read...
Hi,
I am developing a custom board with nRF52811 where I will measure analog signals from op amp on ADC (single ended mode). Signals will be very small, so I need a good...
Hello guys. I'm beginner in Nordic Devices.
I'm working in project that sends Acceleration Data from KX220 sensor over LoRa network or if there is a BLE device connected...
Hi，
I find that nrf52 series can support Bluetooth 5.2 SoC in nordicsemi page, but it still shows Bluetooth 5.1 SoC in Product Spec.
Which one is right ? Is it just that...
In the User Guide for the nRF52840DK on pg 26 is:
8.5 External memory The nRF52840 DK has a 64 Mb external flash memory. The memory is a multi-I/O memory supporting both...
Hi,
I'm working with the USB_CDC_ACM example to communicate with a PC trough COM port. It works well.
Now I would like to use the ISO endpoint feature in order to transfer...
I have a NRF52840 DK, with a pca63511 power profiler kit purchased just a few days ago from Mouser. I am trying to use the power profiler kit with version 2.3.1 of the power...
We are in a need to upgrade the existing Soft Device to higher version from the application firmware. The reason why I am asking this, if it is possible to upgrade then we...
Hi All,
I am Working on nRF52840 and using nRF52840-DK.
Below is my working environment
SDK - nRF5_SDK_16.0.0_98a08e2
IDE - Segger Embedded studio (windows 10 -...
I am using NRF52840 in Mesh (SDK 4.1.0), I am facing this strange issue, one of my node (have client+server both) is got damaged, I replaced this with new NRF52840, then I...
Dear support team,
In the AT command manual, the parameter type are well documented:
But there is no hint or description about parameters in certificate manager. The...
Hi I am using Mesh V 4.0 and Stack V 16.0
I have created the Message Model in Client side and can able to send string from Client to Server on button press.
Now when I...
I am a nRF new user, I try to use JLink-OB (STM32F072C8T6) program nRF52832 module, wire nRF52832 via SWD likes below,
I try to use nRF command Line tools operate nRF52832...
We're trying to make our device automatically recover after a brown-out or brief power loss. I'm hoping to leave a system-state value in a RAM location and check for it on...
