Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi,
I have bought nRF51-DK and have downloaded the hex file successfully in the mbed mode, I wonder May I debug the DK with CMSIS-DAP instead of JLINK? I searched the internet...
I just finished reading the O'Reilly book " Getting Started with Bluetooth Low Energy: Tools and Techniques for Low-Power Networking " where the author uses the nRF51822-EK...
I could run the examples like blinky just out of the box
But, I am clueless how to add a bootloader to this example. I just want to add a simple bootloader from Open Bootloader...
Hi,
we are about to enter bluetooth and expand our products with it. however, the approval process still raises some questions. What I have understood so far (please correct...
Hi everybody,
as already mentioned in the title, I guess to have stumbled across an incompatibility between the app_pwm library and the gazelle link layer.
To keep it...
Hello,
I'm using SDK 15.3.0
I added "err_code=sd_ble_gap_adv_data_set(p_data,31,NULL,0);" to the advertising_init(void) function, but I got the following error:
Error...
MCU: nrf52840
SDK: V 15.3.0 with nRF-IEEE-802.15.4-radio-driver
problem:
I tested repeatedly connection with my nrf52840 production (peripheral) with andorid phone...
Hi,
I have downloaded MDK Keil software .so the problem is if i click on + sign in all devices in pack installer it is not expanding and also i am getting like this
if...
Hello All,
Greetings!!!
I am working on nRF51822. I am used custom board. For reference i used nRF52 SDk 8.1.0 in IAR.
Right now i am use gpio pin as an interrupt pin...
I send 25 byte long messages to unicast addresses in a Mesh network. Because of their size messages become segmented. access_model_reliable_publish() is used for sending....
Hello,
I am using a combination of several Nordic devices and hardware. The nRF52832 is used in a sensor to collect light level information. That data is transported over...
Hello,
I wrote a simple program to turn on externally connected LED at Port 1 and Pin 10. But it is not working. See the code -
#include <stdbool.h> #include <stdint...
Is there any documentation about how to configure the SoftDevice clock configuration using the RC as SoftDevice clock source?
My target is the nRF52832 with the S132 Softdevice...
Folks,
We're wondering how the soft device can work with it being provided as a hex file? Usually with things like this you'd get object code to link to, but that doesn...
