Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
I am currently working on a project for which I use the Secure Serial UART Bootloader from SDK 15.3 (nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10040_uart...
this device has 2 batteries. so I am adding 2 of battery service UUID(0x2A19). but I cannot access the other of UUID via windows API. but nRF connect for mobile can access...
Hello,
I am trying to use the BMD-350 evaluation board to program a standalone BMD-350 module on a custom PCB. I have followed the instructions in the documentation to connect...
Currently, only one ble_peripheral(based on nrf52840) can connect to the gateway (based on nrf52840) .
The other ble_peripheral( based on nrf52832), will bond to the gateway...
Hello,
As our product (nRF52832, SDK14.2) is heading to radio certification, I was playing around with the DTM example but have some open questions.
I've flashed the...
Hello,
ich have a custom board (with nRF52840 chip) which is programmed over SWD. So the Port ist easy accessable. As base software I am using example/radio_test.
I...
Dear All,
We have designed our custom board based on nRF52810 chipset. wehave not used 32.768khz oscilator. it seems in code default configauration is with crystal. so please...
Hi I'm trying to get started with the the nrf52 Dev Kit and the Bluetooth Low Energy tutorial series, I've downloaded the first example "nrf52-ble-tutorial-advertising" from...
Hi,
I m using NRF52840 as a Beacon. i m using SDK15.2 ble_app_beacon.Advertising is works fine. Now i want to change advertising parameter while button pressed. Here is...
I have the eval board pca 10001. After compiling the demo app for nrf51822_xxaa (256k), keil displays "no cortex-m sw device found" when I trying to flash or debug from their...
Hi,
After provisioning a device using PB-GATT there is a 10 second delay after the PB-GATT connection is closed and the first Mesh Proxy Service advertisement is sent. ...
When I call:
zb_set_network_ed_role(ZB_TRANSCEIVER_ALL_CHANNELS_MASK);
to search for a network across all of the possible channels I can't connect. I can only connect...
Hi,
I'm wondering if it's possible to implement Wireless HART protocol using the nRF52?
If yes, can someone point me the right way (open-source libraries, etc)?
Much...
