Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
.y device keeps restarting multiple times without any warning which causes messages to be delivered multiple times to nrfcloud. I've had 5 messages delivered simultaneously...
Hello everyone,
Testing on:
nRF52DK (PCA 10040)
SDK 13.0.0
I have been struggling with reading from the register of ADS1299. I just want to try to read info from...
Since Commit https://github.com/NordicPlayground/fw-nrfconnect-zephyr/commit/bd7569f272882f105515acda04e45e7878a68e13 the cmake build on Windows is broken (see also https...
I am getting this message with constant reboots.
Nrf_cloud_connect failed: 60
Used tracker application. My device doesn't even show up in nrfcloud.
The at client application...
I'm checked out at today's current head for fw-nrfconnect-nrf ((ecc4ded86716fcf4b94e80efca450b3ddb4b7a26)) and have run "west update" to sync all repos. My modem is loaded...
I am modifying the twi_sensor project ( using Segger studio ) I want to add support for TWI 1, I have enabled it in the sdk_config.h file:
TWI 0 works fine as expected...
Hello sir, Mayur here can you please help me out with the interface of data from NRF52832 and ESP8266. I am facing some problems as i am not able to communicate the NRF to...
Hello,
I am using the nrF51 DK (PCA10028 board) which has been programmed with the Softdevice 130 in the Keil uv5 IDE on windows 10. I am working on the proximity application...
Hello,
In an application I am using NRF52832 IC as central. Before uploading code in every board, I need to change the device name and compile. This process is consuming...
Hi Nordic Team,
I'm having some trouble with using the nrf_calendar with the softdevice...
I'm using the SDK V12.3.0 and softdevice s130 V2.0.1 and the exemple ble_central...
I read a few questions there were related to this, none that i encountered seem to give me an answer.
I am using SDK15.1 nRF52
I am NOT using dynamic allocation, I need...
Hi,
I want to connect NRF51822 wit NRF51 development kit over the air i-e. Development Kit would work as server (look for available client and connect with it and then send...
Hi,
I am using nrf51422 dk board in my project. so i need to use Bluetooth in my project. Could you plz tell me the which version of SDK do i need to use for this Bluetooth...
Hello to everyone.
I'm working with chip nRF52832 (PCA10040) and Mesh 3.1. I'm trying to connect a HC-05 Bluetooth/Serial Module using its serial pins (Rx/Tx) to the default...
Hi,
I am using SDK 15.3 and NRF52840 Preview DK
I have a requirement where I have to glow one of 3 LEDs R-G-B (each connected to one gpio pin) for 1 second and turn...
