Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
Hi all,
I'm currently working on adapting this example to fit my needs for testing a Bluetooth Mesh network.
I want to add the functionality for nodes to send to each...
Hi All.
I am aware that the USB nRF52840 Dongle does not support debugging but, can this device issue AT commands to a remote nRF52840 module in order to check the value...
Dear,
After adding the peer manager module of the SDK 15.2 and some other codes about configuring static passkey in the example "ble_app_uart" in ble_peripheral, I can successfully...
Hello,
I just install the nRF sniffer and have some trouble.
I use the following software version :
- Wireshark 2.6.4
- python 2.7
- pyserial-3.4-py2.py3-none...
Hello,
I am currently sampling SAADC every 1ms using PPI. Samples are collected in predefined buffer, and then send over BLE with ble_nus_data_send() function.
I would...
If I use sd_app_evt_wait() or nrf_pwr_mgmt_run, I lose TWI. In other words, in order to use TWI, I need re-initialize it. If I use:
__SEV(); __WFE(); __WFE(); It works but...
Hi,
The NRF52DK we use is interfaced to a capacitive touch keypad and an RGB LED. The board works fine when supplied by the USB but when we try supplying through the external...
I am trying to update the firmware via OTA , while uploading the firmware I am getting "upload failed" message on the nrf connect application.
I am using nrf51422 board...
We currently are investigating a move from nRF52832 to nRF52840. The reason for this is that we need a more powerfull radio - more range (even if that means lower throughput...
My environment: DK 10040, nRF52832, SD 6.1.1, SDK 15.2, SES 3.52
When does the SAADC use power? And when does it stop using power?
I searched the 52832 specification and...
I am trying to run the example from this page: www.nordicsemi.com/.../Getting-started-with-the-nRF52-Development-Kit
I have PCA100040 somehow after running blinky and others...
I am trying to get a driver from a third party binary to work. Their library was compiled without using the HW FPU. I had to compile my code to use the softfp. I also added...
I posted on the Adafruit forum but there doesn't seem to be much support there. Since the module is based on nrF I'm hoping this community can help out.
For the most part...
hi,
i am using nrf51422 ble_app_uart(sdk 12.3.0) example
i am receiving a string through app_uart_get() function, i want to compare it then i have to send some predefined...
SDK15, s132 6.0, nRF52832
Hi!
I need to know before connect on the central side (from advertise data), that this piripherial device has already bonded.
Is it possible...
