Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hey, i’m working on implementing the adafruit_tag_reader example from the SDK v13.0.0 on my Thingy 52. I have copied almost all the code from the adafruit_tag_reader example...
I modified the FW "ble_app_uart" using the example "Nordic-SDK\nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral\en_app_uart\". I added the pairing function and "delete_bonds...
I want to connect 2 SPI slave with on instance. Issue is to mange chip select pin. I went through few post, people suggested to check SPI manger library. I am not able to...
Hello
We tested our product integrating the nRF52840 vers. C in DTM with the Anritsu MT8852B.
The RX tests (PER and sensitivity) pass but all TX tests (Output power, modulation...
Hello,
In my application I'm putting the NRF52832 device to the system off by calling the sd_power_system_off() function.
When it occurs at the start of the program -...
Hi are the example applications for use with the mesh provisioning app available for the nrf52840 as well as the nrf52832 devkits, or just for the 52832?
Best Regards, ...
Hi,
I want to add my own data into beacon advertisement packet. for example I want to add my data as "ABC0001", and it should be available in advertisement packet. How...
Hi all,
I am using the Power Profiler (v2.0.0) in nRF Connect (v2.5.0) to debug and profile some nRF52832 applications, and I cannot seem to find any button that allows...
(開発環境 ) OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex?-M4F 32 bit...
Hello,
I am using SDK 15.2 with softdevice 140 on nrf52840 board. I have been trying to get the development board to pair with a peripheral sensor with UUID "E7D4AA0F-5ACB...
I would like to know how to compute or optimize the maximum number of BLE device (in advertisement mode) that can be detected by a Scanner (Smartphone app).
I can not find...
Hello
Is there any example code in the Zephyr for operating as the Mesh provisioner/controller using the serial mesh interface on the nRF52840.
I am working on using the...
I'm having a peculiar problem with my device in a memory heavy application, two of my libraries use statically allocated memory and one uses what i allocate with mem_manager...
Hello.
I'm working for a Zigbee networking project.I chose nRF52840 as the coordinator.The coordinator acts as a gateway to communicate with Zigbee 3.0 devices on the market...
