Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi
I open the SAADC to get the battery after initial the SAADC, using nrf_drv_saadc_sample_convert to get the ADC data . After nRF52832 is initialed, it enter power_manage...
Hello I'm using a nRF52810. Now i'm trying to add an PCB antenna to my Altium sheet i Wrote in another Reply that i could use the one from your USB Dongle but i don't find...
Hi there,
I need realtime data monitor, but the power consumption is too large when BLE sending data continusly. So I wanna know wheather NRF52832 support package the...
Hi,
I am not yet familiar with NFC.I s it possible to read battery data from the NFC tag of the nRF52 to another device (for example a smartphone). I want to write simple...
Hello,
I am in the process of designing a new custom board with the nRF52832. Apologies for the silly question, but swimming in the documentation at the moment, and I need...
HI, we want to develop DFU over NBIoT network (UDP), and we would like some advice on how to implement that. We are using nRF52832.
Looking at your SDK examples for BLE...
Hello Everyone,
I am trying to integrate LIS3DSH accelerometer with nRF52832 development board(I2C communication). I have Implemented Wake-up State Machine for LIS3DSH....
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Hi folks,
I've found no beeter way of reporting this (no public SDK repo which allows issues with code reference).
I tried to TX ESB DPL frames from an nRF52840 to different...
Hi all,
I want to sell a device that I have made that uses the nrf51822 and the app inside the chip is derived from the ble_app_uart. It uses two chips that communicate...
When I send my app to people, it uses a specific version of pc-ble-driver. I would like to make sure dongle used was programmed with the hex file package with this specific...
Hi,
I'm having issues with my nRF9160. I followed the steps under "Getting started with development", but I keep getting the following error when updating the mfw:
I...
Hi
I'm using the NFCT peripheral of the nRF52832 Rev. 1.
The state machine (figure 118 in PS V1.4) shows that the NFCT can be activated by either issuing the TASKS_SENSE...
Hi ,
I am using the secure bootloader example (SDK 15) as a template for my DFU solution.
I am experiencing issue with the update process as the device shuts down after...
Hello
In our project we are using NRF52840 SoC.
Up to this point NRF52840 chip is used as BLE module to be able to connect our device to cloud over gateway.
now we are...
