Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi ,
I am working on application in which I am using GPIO pin to detect interrupt. GPIO pin normally has logic low level. When it becomes high level I have to generate...
We develop BLE server application on nRF52840 with SDK 1.5 using nRF52840-Preview-DK.
The application is built as multi tasks with freeRTOS where BLE is one of the tasks...
Hi,
I am using Keil uVision 5 and SDK 15 on nrf52840 development. NRF_LOG_ENABLED is set to 1 in sdk_config.h
But NRF_LOGS are not being printed in Debug(printf) viewer...
Hi,
when the micro go in: idle_state_handle(); I have 2 possibility:
If the soft device is present use the first instructions else the second.
This is correct, but...
Dear nordic,
I have an BLE application which works as Central and Peripheral and also which contain ADC,UART and GPIO's
Scanning and advertising controlled by application...
Hi Team,
We have observed that without power supply we are seeing 1V power at board Vcc. Without giving power supply to board.
Why is this happening?
We measured GPIO...
I was trying to verify boot loader using the provided script. I noticed following abnormality.
--It often fails to verify and show the following error:
Reading UICR...
Hi
I'm running nRF52840 MCU at 1.8V, and trying to use the dev kit (PCA10056) to program the external nRF52840 MCU.
According to the datasheet, the dev kit runs on...
Dear employee
for bug 89，
According to <nRF52832_Rev_1_Errata_v1.8>
It is mean below?(spi with blocking mode)
But I think it should be this
when transfer...
Hi Support ,
I'm estimating the average consumption of nRF52840 chip .
Regarding the BT consumption , I used the Online Power Profiler an got the results . But these...
Hello everybody, I've got some of nodes for the light switch example. I'm working on nRF52832 chips. I tried to find answear for my questions, but i didn't. I want to create...
Using the nRF52832 device with the S132-v3.0 soft-device (s132_nrf52_3.0.0_softdevice) and SDK version 12 (SDK120200F12) (Customized for our application, which includes use...
Hi, I need to read a pulse signal with the nRF52840 . I tried to use the timers but it seems to go in conflict with the I2C that I use to communicate with another device....
Hi,
I am trying to make a simple function for writing via SPI. I am using the SPI example and it works fine. Now I would just like to make two SPI functions that I can use...
