Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi
I wonder if the SDK DTM example can be used with a Rhode & Schwarz CMW500 unit. Are the commands compatible with each other, i.e. expected by the CMW500 and DTM example...
Hi,
we're evaluating NRF52 as a platform for a project in the agricultural space and I have some beginner's questions:
Is it feasible to use a timer firing at 100kHz...
Hello,
I created a custom board with the BMD350 module (it has a nRF52832 chip), and I a trying to program it with the BMD300 eval board.
The module on my custom board...
I am using a nRF51422 device with the SDK 11. The task is to transmit battery service data to an application on the phone. I was wondering if there is a tutorial available...
Hi,
I used "ble_image_transfer" sample code and can get the all the stuff I want and now I'm implementing the central device for it,
but somehow I always got the "cccd_configure...
SDK 14.0.0/S132 5.0.0
When a whitelist is in use and during a connection, a call to ble_start_advertising is made to change advertising to a non-connectable type
since...
This keeps happening every time I stop the program for a while and then resume execution.
N.B. I did put a breakpoint trying to catch the problem.
Softdevice s132 6...
Hi All,
I have more boards on which I have loaded the code ble_app_uart_c (nRF5_SDK_15.2.0_9412b96) which I use as central devices and I have other boards on which I have...
I need to send the following sequence of bits through TWI
start bit | 7 bit address | write | slave ACK | stop bit
I looked through the twi_hw_master.c and it seems...
When building a project that compiles the hal_nfc_t2t.c, it errors for nRF52840, but works for nRF52832.
For the nRF52840, I get these errors:
Looking for some of the...
Hello, I want to transfer a large file (approx. 1.5MB) over BLE using nRF52 Module in a way where BLE Host and BLE Controller will be on the nRF52 SoC and the application...
I added ams service to my project, and I tested with my iphone 7P, seems all goes well. But today I tested with my iphone 5S, sometimes the hardfault exception raise.
Hi Nordic,
I'm trying to use a nrf52832 dev kit (v1.1.1) with NRF Connect (v2.5.0 on mac) to communicate to my device (NRF52832). My device has implemented MTU exchange...
Is there something on the specifications regarding the structure of a node? We have a node currently with 3 Elements:
El0: Light controller: Config model, Health model,...
