Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello guys,
everything worked fine for me (NRFConnect, Apps, CLI, Building with Segger Studio, Prgramming via NRFConnect Programmer, everything on Win10) but then I was...
Hi,
I am using nRF52832 DK for testing beaconing and TWIM and TWIS. I am using SDK 14.2.0 S132 v5.1.0.
But, the final product would be using nRF52810. So, will the code...
I'm working on a project with nrf52840 and i'm trying to send and receive ipv6 packet throw thread protocol so i tried to use to send with otIp6Send and receive with otIp6SetReceiveCallback...
Hi,
Is there a detailed analogue circuit model available for the GPIO pins on nRF52. Most of all, I am interested in the circuit model (or SPICE model) for the IO pin when...
Hi, I am currently working on calculating a Li-ion battery;s remaining capacity. As far as I know, I should read the raw value via SAADC. then convert the value back to voltage...
Hello, everybody
I got a problem that i add device name and advertising my specific data according to Beacon example in SDK 15.2.0, but the data order is not what i expected...
Hi，
DMX512 protocol is USITT（United States Institute for Theater Technology）Prescribed agreement
I want to follow this agreement to design
============ DMX512 protocol...
Working on nRF51822 QFAB custom board.
I loaded nRF51822 Beacon v1.1.1 Precompiled hex file in custom board.
Keil 5 Uvision iDE
Windows 7
But I loaded examples programs...
Hello,
I'm developing a solution based on nrf52832 that must be maintained for many years. I want to update my application but also softdevice.
I managed to implement...
Hi,
We are using nRF52832,want to configure non standard baud rate 5787 as per our client request,
Is there formula to calculate the error and reg values please advice...
The errata for the nRF52832 WLCSP states -4dB sensitivity hit using the DCDC converter and -2dB sensitivity hit using the LDO. Will this be fixed in the final revision of...
Hi,
I'm looking at the Generic Power OnOff model available in SDK For Mesh v3.1.0.
1. Why is there a `generic_ponoff_setup_server_status_publish()` when the setup server...
recently, I learn how to use the nrf52832 soc in pca10040 board, and want to use the sdk5_15.2.0 to test all the examples project from "peripheral" to "ble_peripheral".
...
