Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi
I am trying to port an SPI driver from a project for the NRF51822 to an NRF52832 and running into a problem reading more than two bytes. We are using SPI0 (not SPIM0...
Hello,
I'm using an NRF52 DK board.
I noticed that when I change P0.27 from the default (input / not connected to input buffer) to being an input pin connected to the...
Good evening,
I had a question in respect to the exact procedure needed to read a characteristic with read permissions. I have just discovered a service i would like to...
Board：PCA10056 （0.9.3）
SDK：15.2
Softdevice：S140
Example：ble_app_blinky
Today，I follow this page Using an ampere-meter for current measurement to measure the current...
Consider the following sequence of events:
1. `health_server_fault_register` is called, and it saves the current publish period.
2. Config server receives a message...
Building ‘Smart_Remote_3_nRF52_Firmware_nRF52832’ from solution ‘Smart_Remote_3_nRF52_Firmware_nRF52832’ in configuration ‘PCA20023-SR3_nRF52832_Product_Example’ Assembling...
Hi, Nordic,
I am using the ble_app_uart example in the SDK15.2.
I find a issue that when the device, which p_client->is_notification_enabled is already true, is disconnect...
Hi,
I just started with Nordic nRF52 DK and builded and flashed nRF5_SDK_15.2.0_9412b96/examples/ble_peripheral/ble_app_gls application on Ubuntu 18.04 using armgcc toolchain...
I'm experiencing a problem with the NFC.
I'm trying to make a simple read-only tag, and I've used the NFC Text Record Example to build upon. That worked without a problem...
Just wondering if you have a desktop application that can load secure packages onto nrf52840 boards?
As far as I can tell nrfConnect for Desktop can only load a firmware...
I am using PCA10040 with S132.
I am using PCA10056 with S140.
I have a Teledyne BPA Low Energy sniffer that does not support BLE 5.0.
When using programs (e.g., Multilink...
Hi,
right now I'm trying the example with Dynamic multiprotocol examples using nrf52840 Thread and Zigbee SDK, but when I build it, for example : BLE Proximity and Thread...
Hello,
I am working on implementing the USB HAL for the nRF52840 for Mbed-OS's upcoming USBDevice feature release. I am encountering an issue where the automated test suite...
Hello
We would like to know if we erase/write a page beyond the 10K cycles, is the retention time decreasing ?
Do you have a graph or a table of the retention time showing...
Hi,
Currently，the BLE softdevice used for nRF52840 have released. What about the ANT softdevice?
I want to know the release time about S2xx or S3xx. Can you give me a...
