Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
hi!,everyone:
i found if i open the watchdog in the code, it reset the system according to the register CRV, can i close it before it reset the system?
hi,
i am using nrf51422 with sdk13.3.0 and soft device 130
i want to send 69 bytes of data,which is the best way to increase packet size
By creating custom service,can...
Hello All,
I made 2 custom boards, both mount a n52840 QIAAC0 chip. I was able to program them using the "ble_app_uart peripheral" and "ble_app_uart_c" codes that I found...
Hi,
Board: nRF52840 PCA10056 Development kit
Keiluvision 5
SoftDevice : S140
nRF-SDK 15.2
SDK example code: ble_app_uart
Hi, I want to change the BLE range...
Hi,
nRF905 is still manufactured, right? I didnot see anything on Nordicsemi, but I've seen on Farnell's web page "No Longer Manufactured" and on digikey it was not available...
Hi!
I'm using nrf8001 to send twenty 20-byte packets to a phone application. The connection interval I use is 30ms. However, I takes 5 seconds to send the data to the phone...
Hi, I want to advertise each 3times every 5seconds as sometimes beacon scanner can't read it so I need 3times in series advertising.
in main() I added 3times advertising...
Hi there, I am working on NRF52 DK, SDK15.2 with SD 6.1.0, The issue I am facing is that the DFU service is appearing on Android device and I can update apps using NRF toolkit...
I am trying to connect nrf52832 with custom android app, after connection established beacon sends message. Sometimes I can establish the connection after 8 tries, sometimes...
Hi,
I'm working on a project which uses two nRF51822 (SD130 and SDK v11.0) on mobile devices. Device A is continously advertising and device B scans for a fixed interval...
I'm looking to sync an ADC reading with the PWM output. I'm using PPI for this but fails to make it synchronise properly with the PWM.
I'm getting interrupts and sampled...
Hello,i am using nrfsdk with softdevice 6.0.0 in my application and by using it i am trying to connect my mobile uart application with my BLE .but i am facing some issues...
Hallo all
I have an appliation using the LOG for TX output to uart,
I want to maintain this code but to add RX based on the app_fifo_init,
how can they coexist ?
thanks...
Hi,
I would like to use the nrf52 as my bluetooth end device, which inturn has to communicate with the Bluetooth IOT gateway like Rigado module or Nordic gateway APP(which...
