Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hello!
I would like to know what are the minimum, maximum and recommended current values for the VDD, VDDH, VSS and VBUS supplies. The voltage values are listed here...
Hello,
Im trying to flash RAYTAC AN54L15Q-DB board but im keep getting following error:
Error: One or more batch tasks failed: * 1050050051: [Probe] Emulator error: Failed...
Hi,
We are doing RF Test for nRF52840DK, and we are using CBT Bluetooth tester. Commands are going to CBT fro nRF board.
My Question is code we need to flash for RF test...
I am using the Nordic nRF5340 DK to communicate with the ICM-42688-P sensor via SPI. However, the sensor does not respond to the MCU's commands. After observing the SPI clock...
Hi,
Previously it was possible to download the old nrf5 sdks from for instance this url:
developer.nordicsemi.com/.../nRF5_SDK_v15 .x.x/
but it seems to not be available...
Hello,
I'm trying to read the build info of the Bluetooth LE controller using BT_HCI_OP_VS_READ_BUILD_INFO, but I get the following warning:
<wrn> bt_hci_core: opcode...
I am using nrf5340dk and I am facing an issue. I have configured SPI on my dev kit and the screen I am using with it is operating at 5v but the dev kit has 3.3v max. So I...
Hello,
I am trying to find a simple example of how to setup and run the SAADC on the nrf5340 in continous mode.
I would like to use the internal timer and only need to...
The broadcast interval is 2s, and the power consumption is 7ua on the DK board; On this basis, the power consumption when using an external low-speed crystal oscillator is...
Hi,
when DC/DC is enabled, current consumption in sleep is higher than when using LDO.
This is consumtion with DCDC = 0
This is power consumtion when DCDC =...
Hi,
I am struggling getting my production programming script to work in a way where I get everything programmed including the App being validated...
For some reason it...
Hi,
I have tried the BLE image transfer demo and I really want to have the similar function about the real time data rate calculation. How could I do that? I found there...
Hi,
We are using nRF52840DK. Our main object is to collect the log for the BLE. We have installed the nRF Sniffer software and wireshark tool to extract the BLE Packets...
Hi,
We are using nrf52840 QFAA with our amplifier that gives ADC values at 100hz. We need to process the data via low pass, band pass filters, median filter, moving average...
