Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hello,
I've been working on a project using nRF52832 + NCS 2.1.1 including BLE and some sensors : MAX86150, MAX30205, MP34DT05, LIS3DH
I'm sending data of these sensors...
Hello! What are the steps I need to take to switch from BLE protocol to lets say the Gazelle protocol? Is it as simple as disabling the Softdevice? If such a function exists...
We are finishing up development of our product and looking into creating our Bluetooth listing. We are using the NRF52840 SoC (Fanstel BT840F model) with softdevice and NRF...
Hi,
I am working on an application using the nRF52840 with the Quectel BG96 modem. I can successfully communicate with an insecure MQTT broker using the BG96 modem. Now...
Hi!
I'm making a new board using nrf54l15 and I found the following issue:
/* * PWM signal can be exposed on GPIO pin only within same domain. * There is only one domain...
We have a custom board with the NRF52840 running NCS v2.8.0.
We have a problem where our device will crash/lockup. From our testing so far, it seems to be related to Bluetooth...
I have a project for the NRF5340 with SDK 2.6.1. I test the code with twister using Unity and CMock. That works great. But now I have to adapt the unity_cfg.yaml (which is...
Hi,
DK:NRF54L15
Modify form the sample code:peripheral_uart
I add one spi21 and k_timer to get the sensor data, periodically. But got the error ZEPHYR FATAL ERROR 4...
Dear Nordic Support Team,
I am working on a project to measure distance using two E73-2G4M08S1C nRF52840 modules. I would like your guidance on the best approach for implementing...
ide :- segger embedded studio I have a problem regarding BLE_UART.
I am using Segger Embedded Studio. I want to implement Bluetooth, so I used an already existing code in...
I want to do DFU with secure keys on nrf54l15dk. I want to receive in my application new firmware and store it on internal flash of the nrf54l15 (i have memory to store the...
Dear Nordic Support Team,
We are using the nRF5340 together with the NPM1300 in our project. The 1.8V output is controlled via the NPM1300.
When performing a BLE DFU ...
Hi,
Could you please give us some power budget comparison regarding connections using CoAP vs MQTT and other protocols (UDP socket...)?
We are thinking on a nRF9151 design...
Hi all, Relatively quick question. I have a production implementation where the COMP "Cross" event is wired by PPI to a GPIOTE "out" task. The Comp is acting as a UVLO. When...
Using Zephyr V2.8 on the L15. In the uart callback, in the UART_RX_RDY case, can the evt->data.rx.offset ever be non-zero?
It doesn't appear that the offset is ever non...
