Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hey ,
My application stores the data on BLE disconnect to pstorage succesfully.
But on reset if i try to read the data from pstorage it stops advertising, but the pstorage_load...
Hi,
I am using nRF52832 with S132_V2.0.0 and SDK_11.0.0.
I am able to doing dfu of softdevice and bootloader individually but when i try dfu for combined (SD + BL) then...
I can't find nrf.exe in C:\Program Files (x86)\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf
I only find nrfutil.exe in that folder.
Shall I use nrfutil.exe...
Softdevices have several separate version number systems:
a) the human-readable release version - used for hex file naming.
e.g. s110_nrf51_8.0.0, s120_nrf51_2.0.0
b...
Hi! I use a smart beacon kit (rev 1.0.0) and I would like to know how long the cpu is blocked during the data transmission/reception. I set the connection interval to 10ms...
We are designing a nRF52 based circuitry based on "53.2 Schematic QFAA QFN48 with DC/DC regulator setup"
In the reference diagram, there is an Optional block for the LFXO...
Hey all,
I've created HIDs using USB before which require a vendor ID (VID) and product ID (PID). Are these necessary when creating a device that uses HID over BTLE? If...
Is it possible for nRF52832 to drive an SPI TFT 240x240 LCD and a TWI Capacitive Touch Panel with BLE and NFC? Is 64Mhz the highest speed?
What I mean is that is it possible...
I am creating a project which must use two spi at the same time , the one store data to flash and the other use to communicate with FT221 .In the datasheet ,I realize that...
Hi Devzone,
We are currently awaiting arrival of our custom board, based on the nrf52 chipset, and I've been tasked with determining any potential gotchas with programming...
Hello,
I am trying to implement a star network with more than one datapipes enabled, where (between other tasks) the PTXs devices have to synchronize their clocks (real...
Hey, I am compiling some code to both read ADC measurements and send the measure it over UART. I looked at the ADC+UART+SOFTDEVICE example on github and I think I am pretty...
Can you please provide me the iROM and iRAM settings for the S110 softdevice for the nRF51822? Specify the SD version you are using please.
I'm reading nRF51822_Development_Kit_User_Guide_v1...
hi
i get vlaue with this line of code
but i did not specify what char should get it value
how can i get value from specific char?
i have nrf51422 v2 sdk v6