I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello,
I tried to do migration on new SD S132 but some elements changed (typedef uint32_t nrf_clock_lfclksrc_t is not defined, ...) and i get a lot of errors.
When new...
I am using the adc to sample a sensor and send this over the air.
For testing I used the simple_uart library and it works.
But now I don't need the uart connection and I...
HI,ALL
Is the scanning device always get the BLE_GAP_EVT_ADV_REPORT Event ?
my current project is
nRF5_SDK_11.0.0-2.alpha_bc3f6a0\examples\ble_central\ble_app_uart_c...
Hi,
I'm using SD110, SDK 10.0.0, nRF51822
In my own application, I control 4 servo by pwm with Timer1 and Timer2,
and I have 2 buttons, each button is a flag for...
Hi now i"m working on nrf15882 ,i'm confused how to test ble_uart example?
when i connect to the device(nrf15822),the cellphone app always displays:connecting,
later...
I'm trying to get a hold of a few nrf905 dev boards. Most the ebay boards have "nrf905 (ptr8000+)". Is there any difference between these chips?
I'm assuming the ptr8000...
Hi,
I setup the nrf51 as in central mode and talking to an ARM Cortex mcu via spi bus with the NRF51 set to slave. The spi communication working fine, but when I star scanning...
Hi.
I'm using PCA10028, SDK10.0.0, S130 and "ble_app_hrs_c" "ble_app_uart_c" as reference.
My peripheral's Service UUID = 000098000000100080000017FFE07A00.
I want to...
Hi,
We intend to use nRF5x as main uC for our upcoming 4 new design. (diff. kind of measurement devices)
Instead of qualifiying each new device, we have intended to...
Is there a list somewhere that correlates the NRF_FICR->CONFIGID value with the actual nRF51 variant?
I had orginally used the 16K Ram versions, but when Nordic release...
Hello,
I'm implementing long write function to my project.
I managed to get it working, but i can't send more than 68 bytes of data.
When i'm sending the data, I slice...
Is there a way to tell if the timer is running? There's a start task, and a stop task, but I'm not sure how to tell if a timer is currently running. The best thing I can think...
Hi!
I developed my application using nRF51 DK with nRF51422 QFACA10 chip on it, and everything works fine. But now i would like to program this application on nRF51822...
Hello,
sd_softdevice_enable never returns.
I have no 32.768 KHz crystal but is set lfclk with NRF_CLOCK_LFCLKSRC_SYNTH_250_PPM.
I'm running my application on a custom...
