Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Greetings,
During a connection between two nrf51422s running on S120 (2.1.0) and S110 (8.0.0) with a connection interval of 7.5 ms I get only a maximum RSSI of -42 dBm...
Hello,
I developed a firmware on nrf51422 with nrf51. I use a development board PCA10028.
With this firmware I control the directly the radio registers (Soft Device is...
I have a nRF51822-EK evaluation kit (so, PCA10001) and am trying to get DFU working with an S120 SoftDevice as per the answer posted here:
devzone.nordicsemi.com/.../ ...
nRF51822
I'm interested in setting up the the POFCON to enable me to get a
POFWARN interrupt when the battery voltage drops below 2.7V.
The softdevice is enabled at...
I have a nRF51422 dongle, and I want to know the power/current when an UART event happens.
I've read nRF51822_Development_Kit_User_Guide_v1.4 p.29 for Current Measurements...
Hello,
I am experiencing some CC register issue in Timer of nRF51822. I am trying to setup TIMER1 for 16 seconds. But I see, that when I try to write to CC registers, the...
The "Intermediate Temperature" characteristic is not coded in the ble_hts.c file.
How could I do to implement this characteristic and maintain the compliance with Nordic...
Hello,
I want to rewritte SEGGER_RTT_vprintf to use sprintf Inside (because it's already linked in my application and allow float display).
The problem is that i don...
Hi
We use the nRF51822 with s110 active. As long the s100 isn't active, we can debug, set breakpoints, stop, continue like it should work.
When activating the s110 and...
Hello,
The question is about CUSTOMER area in UICR. After locking chip wirh UICR.RBPCONF.PALL I noticed that I still able to read UICR.CUSTOMER data.
Could I enable readback...
Hi all,
Google launch uWeave Library project.
uWeave is an implementation of the Weave protocol intended for use on microcontroller based devices.First demo project is using...
Hi,
As first stage of planning our next generation of wireless sensors at my workplace, I must carefully consider which radio protocol suits us best. We don't need sub 1...
HI,
Hi,
I have been working on nRF5 Development Kit where Basic configuration is working i.e. blinky program and when I load peripheral program(PWM,UART), its also working...