Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
I have developed the schematic of connecting NRF 8001 BLE chip with Arduino,the file is attached that contains the schematic. Can you please verify my schematic i.e will it...
Hi, I'm looking for a solution can make a ble device communicates with multiple 2.4g devices at the same time , is 51882 qualified for this? or just by combining both nrf8001...
Hello,
I would like to use the fifo common library but i have an link error. I don't understand that because fifo_app.h is included and contain the functions...
...
Hi
We are using indication to send data to make sure master receive all the package.If we didn't
receive the confirm message,what should we do?Should we send it again in...
I'm guessing it is because the engine powering the site does not support it. But has it ever been considered?
I think it is a powerful way to engage users and build a community...
Hi,
I have two questions about nRF24LU1+.
Q1
Can i change nRF24LU1+ isocheonous endpoints(Endpoint 8 IN/OUT) to Endpoint 1 IN and Endpoint 2 OUT?
Q2
Can i use Endpoint...
Hi,
we’re a group of students at NTNU in Trondheim doing a project regarding bike and pedestrian registration. So far we want to make a solution based on iBeacon and Bluetooth...
Hello,
I am looking into the possibilities of implementing frequency hopping using the nRF24L01+ radio with an external Ti MSP430 microcontroller. I have read that it's predecessor...
Hi,
I want to realize the function of bond, I use "lib_aci_bond(180/* in seconds */, 0x0050 /* advertising interval 50ms*/);'\",.When I click the connect, it can connect...
In nrf51_sdk_v4_4_1_31827\nrf51822\Source\console\console.c,
#include "uart_legacy.h"
But there is no "uart_legacy.h" file in the SDK.
I have to modify to "app_uart...
I downloaded the source for the Android UART app, hoping to hack it into something I can use to test my gadget. But it's incomplete: it fails with the message:
Missing...
I have 3 short questions:
Does S120 support or will support swiching over BLE and Gazelle like S110 does?
Will be able in future to be connected to a BLE...
Hi,
If I want to send data(400Bytes) to client(phone),I must use sd_ble_gatts_hvx to notify client. Is it right?
Every time I notify 20bytes until the end, is it right...
