Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Dear Nordic Team,
After gaining experience with 3G and later 4G LTE-M over the past few years, I have observed a significant gap in the deployment of LTE-M in many countries...
In my NRF52840 based device using NRF5 SDK 17.1.0, I notice that sometimes this loop in the nrfx usbd driver code of the SDK doesn't finish:
[modules/nrfx/drivers/src/nrfx_usbd...
How can I please analyse the latency, reachability and throughput of the DECT NR+ on the nRF9161-DK. I urgently need a solution please, it's for my bachelor thesis. Thanks...
Hi, Im designing a custom board using a NRF9160 MCU. From the product specification it operates at a voltage range of 3.0(2.8)-5.5V. I want to use a 3xLI socl2 3.6v (parallel...
I created a blinky example in zephyr and created my board with Create a new board The build goes well and runs well. The problem is that the device tree gui does not run and...
Hi,
SoC: nrf52840 Environment: nRF Connect SDK v2.4.1
When performing OTA app upgrade all settings and bonds are gone. Settings subsystem seems to be working fine. Settings...
Hello,
I am currently working with the NRF52840 Dongle and have integrated a W25Q512 QSPI Flash chip, connected to the following pins:
CSN: P0.17
SCK: P0.20
IO0...
Hi
I want to know how to get a configuration of a single pin .
I added this function to the blinky example.
But it keeps reporting -ENOSYS.
Testing environment:...
Hi,
I have an application based on the "peripheral_uart" sample code (nRF52840DK, NCS2.70)
As I use interchangeably the same pins as GPIOs and UARTE1, I use UARTE1 with...
Hello,
I been struggling with this issue for a couple of days and can't manage to find the reason behind it.
About the project:
We are developing a IoT device firmware...
Hello all,
i have a problem and I hope that someone can help me.
I can change the bluetooth address of the device with the following code:
and this is okay.
I have...
I work test program on ncs2.8.0.
I put a reference to the BOARD variable at the top of my project's CMakeLists.txt.
When "west build -b nrf52833dk_nrf52833", BOARD is...
Can 52840 dongle program as BLE adapter for development usage like the following URL? Just for development test, so I don't need to buy one.
https://www.amazon.com/ASUS...
I am trying to build the Peripheral UART sample in nRF Connect SDK v2.8.0 targeting the nRF52805 SoC using VSCode. The sample is too large for the nRF52805 flash (linker overflow...
Hi,
I'm having an issue just booting my nRF54L15-DK when building a basic app with TF-M and MCUboot configured, I am using sysbuild to build everything.I am using the...
