Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
On nRF54L15 (NCS v3.1.0), we are using the SAADC with ADC_GAIN_1_4 and ADC_REF_INTERNAL at 14-bit resolution to measure an analog voltage on AIN5. The driver sets ref_internal...
Hi there,
I'm using /opt/nordic/ncs/v3.3.0/zephyr/samples/bluetooth/channel_sounding/connected_cs/initiator and /opt/nordic/ncs/v3.3.0/zephyr/samples/bluetooth/channel_sounding...
Issue
How to properly wake an nRF54L15 from System-Off mode when the device receives a UART transmission, without the use of the LPUART Ready and Request lines or any sort...
Hey Team! We are developing a radio-heavy BLE application on the nRF SDK version v.3.2.4 where we use the experimential QoS Channel Survey feature. In normal operation, it...
Board: nRF52840 DK (pca10056) NCS version: v3.2.3 Goal: Send and receive raw 802.15.4 frames with a custom packet format, without using OpenThread, Zigbee, or any other mesh...
When attempting to install a downloadable app in nRF Connect for Desktop 5.3.0 on Linux, the installation fails with an EISDIR: illegal operation on a directory error. The...
As mentioned in subject,I try to study course with CMSIS-DAP,now, chip recove and flash is OK,but blocked at debug step for 2 days now.
Maybe I made some wrong config some...
Hi, I am having troubles with flashing my first code to the MDBT53V module. I am flashing via JTAG cable, from my nrf52840DK using vscode. According to my measurements the...
Board: nRF54LM20A DK NCS version: v3.2.1 Sample base: nrf/ samples/zephyr/subsys/usb/cdc_acm
Background
I am evaluating power consumption on the nRF54LM20A DK before...
Hi：
What is the maximum number of targets that a DFU distributor can support for simultaneous upgrade, and what is the upper limit? I haven't found any detailed explanation...
In nRF cloud, in the device list ( https://app.nrfcloud.com/#/devices ) it is difficult to manage larger number of devices because of lack of search and limited sorting. ...
This question concerns the description of the SPI communication Electrical Specifications on page 425 of the nRF52840 Product Specification.
The values for "t_spim_vmo...
Hello,
I have a product with QSPI flash that I would like to use nrfjprog to program the flash part. However, the QSPI flash's VCC is controlled (via a FET) from a GPIO...
Summary
With CONFIG_OPENTHREAD_ZEPHYR_BORDER_ROUTER=y and CONFIG_OPENTHREAD_TREL=n , the Zephyr/NCS build fails to link:
ld.bfd: ... openthread_platform.a(trel.c.obj)...
Hello,
I am currently working on a new design based on nRF9151. This design is the evolution of a previous PCB.
The device uses a combined GPS and Cellular antenna, which...
