Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I think this is a bug report for the VScode plugin
One of my boards shows this error when I try to debug
Nrf52833 custom board connected with SWD on Jlink
I was...
Hey there ,
I am trying to modify the Nordic Radio Test example from the pack installer in Keil
for some reason I am getting "
Resource Not Found
We're sorry,...
hi team,
i am using nrf52840 controller and sdk 16.0 i want to know difference between twi and twim and twis driver apis in infocenter.which one i have to use once i connect...
I am trying to display the p_data received data using below inside NRF_BLE_SCAN_EVT_NOT_FOUND case but I am receiving the below data.
2| 1 |6|1a| ff |4c|0|2|15|ff|ff|0|0...
I am working on direction finding connectionless locator/beacon(AOD). We designed beacon board with nrf52811(build option is nrf52840 DK nrf52811) and antenna array, use a...
Hi Everyone,
I recently updated from SDK 1.8.0 to 2.2.0. With 1.8.0, I configured the nRF9160 MAGPIO and COEX0 in my Kconfig file. But with 2.2.0, I don't see that in the...
Hi,
In SDK2.0.0 version, can the TX_EN timing of nRF21540 be changed through SPI control?
If the timing of TX_EN can be changed through SPI control, how FW implements...
Hi,
The example that I use is from here .
I have to use the USB interface to send and receive data between the host PC and the nRF52840 chip.
In the example, I can only...
Hello all,
I'm using the sample for distance measurement nrf_dm. I'm using the ncs sdk 2.2.0, with toolchain 0.15.1. Currently the sample runs without any change, but now...
Dear Nordic support team, I meet a situation: I have big data array need to transfer("arrayTransfer" with 3072 bytes) to smart phone by notification method. Using timer 10s...
Is it possible/intended to store some application data in the EEPROM of a Thingy:91?
According thingy91 eeprom the region 0x0600 - 0x07FF is used for some configuration...
Dear Nordic Engineers
How can keyboard recognize which PC it connect(windows or MAC)?
If the PC is a window, left bottom key are "alt" or "win" and other
If the PC is...
Hi Nordic team
I am skilled in BLE Mesh and developed BLE mesh at several projects.
At BLE mesh,
1. Provisioner was hard-code consistent. It could be smartphone with...
Hi, I have implemented the following and succeeded storing and retrieving values from flash
Mesh 4.0 SDK Flash Manager - Storing values - Nordic Q&A - Nordic DevZone - Nordic...
