Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
I am developing an NRF52833 application that reads from the I2C sensor MLX90641. Below is the code I am using to test. MLX90641_I2C_Driver.c was originally written for Mbed...
Dears
Th case ID of my old question is 218372.
I were waiting for two weeks. However, nobody responded to me.
I wanted to make a BLE mesh product used NRF52840 and NRF21540...
Hi support team
I'm now based on ncs1.9.0 platform. I check the file "\nrf\samples\bluetooth\direction_finding_connectionless_tx\README.rst", finding that the board nrf52811...
I am working on a project with nrF9160dk to connect with AWS IoT cloud, when I was trying to update the certificate by using LTE Link Monitor, why I am getting errors when...
Hello, I tried to using the nRF Connect SDK with VS Code, however when it seems there are some problem while I trying the build. I have read the similar post and trying to...
Why is it that when I try to build assert_tracker_v2 for thingy53_nrf5340_cpuapp or nrf5340dk_nrf5340_cpuapp I get:
Blinky builds fine.
Also, cleaning projects tend...
Hi,
I've made my own PCB with an nrf52840. Right now I'm hoping to test out the bluetooth and measure my board's power consumption - the only problem is that I can't reliably...
Hello,
I can not find a good example online on how to properly configure nRF9160 DK for i2c. In order to learn the system, I am testing a simple example with the nrf9160...
I just install the NCS in toolchain manager, but after installation, only one toolchain folder is there,no zephry,no examples,
I'm going to play in VSCode.
what should...
I use nRF5340 DK as Central, iPhone as Peripheral.
I start a scan with no filters and in scan_filter_no_match() I check if RSSI is good enough "RSSI > -45" and initialize...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hello,
I am using nRF52833 based BE33 ( Celium Devices ) and using nRF52SDK17.0.2. I am trying to implement my firmware which will consume less current. I have implemented...
We use nRF9160 on our own board. The firmware "Serial lte modem" is installed on the chip with connection to an external MCU. Our custom board has a connection to nRF GPIO...
We use nRF9160 on our own board. The firmware "Serial lte modem" is installed on the chip with connection to an external MCU. We need to publish the JSON messages larger than...
