Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
I'm using the nRF9160 DK board with nRF Connect.
I want to create a driver for an LCD with a parallel interface. SPI is to slow for my project.
First, do you...
I have a question on the gnss event type NRF_MODEM_GNSS_EVT_FIX. It seems there's always the NRF_MODEM_GNSS_EVT_PVT event regardless it's a fix or not. The flag can tell us...
I am writing a program for a Garmin Edge which needs to connect to a power meter via Bluetooth, some of the characteristic / service UUIDs are 4 digits which cannot be used...
Hello,
In the latest SDK version v1.8.0, I have developed my own project based on direction_finding_connectionless_rx demo. Here are two problems I countered.
1. the RSSI...
Hi, I am currently working on nRF52 Thread v4.1.0 .
I am working on messaging transferring using coAP server an client .
previously using CLI commands to detect the ipaddr...
Hi, I've tried signing up for a SUPL licence a couple of times but it keeps getting denied. Not sure why. I have logged into devzone.nordicsemi.com and am using the same email...
Hello,
I am trying to update my Nordic nRF52840 via UART, using the bootloader from the examples (SDK 15.2.0). In the my application another MCU (from ST32) will update...
Hi all,
I'am sending epoch time from nrf_connect(mobile) to nrf52840dk only once,
then i need to update epoch time continuosly with nanosecond frequency
how can i do...
Hi
I am working on a custom BLE NUS using the ble nus peripheral example. I am currently using bluez on a linux machine as client and a nrf52840 dongle as server. I can...
Hi there,
First of all I have to say that I am new to BLE technology development. I tried something using your tutorial and I think I succeeded. The board can advertise...
I am trying to create an application where two or more transceivers can each be moving around with different people and each would know the location of the others relative...
Hi everyone
I'm trying to create a new project using SES but could not able to do that. Just i tried to copy the BLE_blinky project from examples and pasted on new project...
I copied the button project from samples in other drive. Copied the ../boards/arm/nRF534DK_nRF5340 in the new project folder. Then, I changed the names of board in all file...
I am working on an application where I need to start pwm sequence after particular delay (accurate delay of multiple of 100us).
I am quite new to nordic environment.
Here...
Hi!
I'm trying to figure out what is the maximum current I can safely sink or source from NRF9160 GPIO pins.
From the spec I can see that I can expect ~10mA sink/source...
