Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi, I want to run UART on my custom PCB module that uses Wuerth Elektronik Thyone-I module that has nRF52840 chip. The project has just a RX, TX pins (and power supply, of...
Hello,
I'm currently having some issues where my custom board is either experiencing infinite DFUTarg cycle or "no bootloader was found" error.
I have been following the...
Hi,
I'm trying to run some example with ble fota
I've read
http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_nrf52.html#fota-upgrades
and
http:/...
Hi i am using nordic nrf52840 chip.
i programmed one application at 0x27000 address, and now i want to calculate the size of that application code in run time.
i have...
Hi
I have a project as the follow
What I have done:
1. Compiled app.hex ( Configured with my board), works fine.
2. Compiled bootloader.hex ( Configured with my...
Hi, I've adopted the DFU part of the NRF Toolbox app in my own app. I want my app to be bi-langual (English / Polsih). I can do this for all the texts that I've created, however...
Hi,
I had a temperature adc reading accuracy issue in lower temperature such as -40.
It is similar to this post issue ( https://devzone.nordicsemi.com/f/nordic-q-a/80859...
Hello,
My application is built with TFM in order to use mbedtls. I am currently using UART0 to send/recv serial data from another board. If I don't call psa_ps_get_info...
Hi,
We have developed one application using nRF52832 SoC and Sdk v15.0. For our application we have use ble_app_uart example as a peripheral and multi-link central example...
Hi,
I am using s112_nrf52_7.2.0_softdevice with nRF5_SDK_17.1.0 and iar embedded workbench. I can flash and run the application without any problem but when i try to program...
Hello Devzone,
I am trying to run timeslotted 802.15.4 alongside BLE using NCS. I have started from this example, replacing the propiertary RF calls with calls to 802...
I was able to set up 2 thingy91's using the nRF9160DK to update the firmware and the asset tracker is working on the 2 thingy91's. I've tried to provision the DK and I get...
Hi,
I am trying to port the nRF5_SDK_17.0.2_d674dde\examples\nfc\writable_ndef_msg and my linker cant find the definition for the following symbols-
linking... .\_build...
Good afternoon ladies and gentlemen,
Just a really quick question/observation... am I going bonkers? or is the link to Segger Embedded Studio on this Nordic Page incorrect...
