Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
I'm trying to duplicate the boot behavior of a Thingy91 on a custom board, i.e. SW4:BOOT and SW3:BUTTON on power up, but the switches available use different IO. I'm wondering...
Hello, I am pretty new to using the Nordic products and was wondering if there is a simply way to write a text file from the nRF52840 to a pc. The system is required to log...
Hi Guys,
I know there are a lot if topicks about issue with "sd_softdevice_enable". I read them all and nothing help me. I'm using Eclipse IDE.
Im using a nRF52840-DK...
Hello,
I have recently switched my OS from FreeRTOS to embOS. I am now replacing the SDK files so my project will not be using FreeRTOS. I replaced the file app_timer_freertos...
hello,
I am trying to learn how to use the nrf52480 dongle and am trying to run the ble_connectivity example. I built it using Segger as is, no changes from the pca10059...
Hi!
I'm trying to sniff BLE advertising traffic using nRF Connect for Desktop on macOS and a nRF52840 Dongle.
I am running nRF Connect Desktop 3.8.0 on macOS Mojave 10...
I have done everything to install the VS code, installed Connect, Toolchains, SDK, Seggers etc. as in the help, but this is the result in VisualStudio Code:
It just keeps...
Hi,
The following code has been working fine since it was taken from the examples (NRF52840).
We wanted to remove the app_usbd_event_queue_process() so we enabled these...
Hello,
I have beacon advertiser and scanner. Scanner is scanning the devices from around. But its not scanning the device that i used for advertising. On the other side...
Dear Sir,
for my nRF52840 application made with the SDK v17.0.2 and S140 Softdevice I'm adding the peer module to a peripheral device example (UART with SAADC with timer...
I was trying to create my own sdk_config based on "$NRF_SDK/config/nrf52840/config/sdk_config.h".
I noticed it contains both the "NRFX" config and "Legacy" configs.
For...
I would like to change the GAP_DEVICE_NAME defined in nrf_mesh_config_app.h by DIP switch. like "nRF5x Mesh Light 1" or "nRF5x Mesh Light 2"
I have modified the light_switch...
Hi everybody, i get this error on a nrf53 with hr_coded on network coded, and UART example modified with multilink and coded_phy, tested by me on an nrf52.
The issue is...
