Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I am working on putting my NRF52840 to sleep with the RTC running (System ON WFE, not System Off). According to the datasheet, I should be able to call a soft reset and keep...
Hello, I am having some problems with what i assume is the readback protection. Is it possible to update the firmware of the device without deleting UIRC (serial number among...
I am using nrf52 chipset, I just want to know did anyone tried to run docker container to create ARM image? I am thinking to use Docker container as CI.
Hello
I am using nrf52832 and ble_app_uart of SDK v17.0.
I am sending data to the app every second through the notify function. If I try to disconnect and reconnect Bluetooth...
Hello,
Is the Power Profiler Kit II (PPK2) only usable for nRF product line and custom boards, or can it be use beyond the nRF line of products such as boards not made by...
Hello!
I am currently working on a project with my nRF52832 that is using BLE communication with a android phone. I have tried some of Nordics' examples that use BLE, but...
Hi all,
I have a question concerning the nRF52833.
I'd like to know if there is a safety limit on the amount of reflected power that is reflected by the antenna inside...
Dear Nordic,
I changed the value in the Bootloader to not erase the 4k just before the bootlader.
NRF_DFU_APP_DATA_AREA_SIZE 4096
In the app I changed the rom size...
Hi,
I dont know if this is the right forum to ask, but is there any common solution for certificate renewal?
For example If I use azure iot hub, I will provision the...
Hi everyone
I apologize in advance for any possible mistakes.
I am new to programming nRF52 series microcontrollers.Having started exploring various possibilities, I ran...
Hi,
We've been developing our application using pc-ble-driver which communicates with a PCA10040 devkit with SD API v5.1 connectivity firmware. In this dev environment,...
I'm trying to connect to a few sensors on the Nordic Thingy:52, and it fails with the following message: characteristic is not defined. The connection to the Thingy is established...
Hi,
i use nrf51822 and sdk 11.0 . I am using the ble_app_hrs_c example .This product consists of two devices，One master and one slave.
The master chip is nrf51822...
I am using the nRF52840 (with SDKv17.0.0 + s140_7.0.1) and made a custom FW based on the ble_app_hrs example. My custom HW has a 64MB S25FS512S flash memory chip.
I found...
