Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hello,
I have purchased this device to use as a BLE sniffer. I have followed this manual to configure the device as a sniffer:
https://infocenter.nordicsemi.com/pdf/nRF_Sniffer_BLE_UG_v3...
Hello.
I'm using a nrf52 dk (nrf52832) + GCC 9.2.1 (9 2019 q4 major) + WIN10 + CLION and I'm trying to build an example project using GCC.
I get the following error: ...
Hello everyone ,
I have question about saving the configuration of Friendship so-that after rebooting the SOC, the friendship's configuration restored without applying the...
Hi, I'm HongJae.
I'm developing a Bluetooth peripheral program with nrf52.
Briefly,
if I send a hexadecimal message(e.g 0x35), GPIO's are ON.
After 1 minute from...
hi,
I found a interesting thing：I use the output function to configure the P0.14（nrf_gpio_cfg_output(14)）. After configuration, the normal output should be low, but it outputs...
hello all,
i am using nRF52832 SoC in my project and my requirement is to write some configuration into internal flash when i flash the program using segger j link.
for...
Hello.
I am evaluating with nRF52833 DK board. I checked both peripheral/uart and ble_peripheral/ble_app_hrs.
Examples work each well on nRF52833 DK. I want to add the...
Hi support Team,
Following are my Questions.
1. Please recommend me three development boards from Nordic. I would like to build the mesh Network.For example one will transmit...
I am seeing a number of issues, but since they appear to be different, I will use different threads.
Setup: have gone to ble_blinky example to keep things as simple as possible...
Hi, i am new to the nRF52840, i like the features it has and i want to create a board using it. In the datasheet it is said to have 2 ARM processors and i want to use it as...
About 3.7V Li-Po battery on spec., can we read adc value from the battery using p0.04(A1) without external voltage divider circuits? In fact, 3.7V battery outputs 4V ,seeing...
Hi,
I'm now planning to test BLE AoA using nRF52833 DK. For now the DK doesn't have antenna array, so I plan to use an addon board like below:
Is there any link or example...
How can I define paths in SES (Windows), like $SDK_PATH, for my project?
- if they are defined in macros, what is the syntax?
- is there a standard variable that has a...
HI there,
I wanted to use nrfx spi with nRF5 SDK 17.0, but it was removed. I checked that in nRF5 SDK 15.3 it should be available, but when I downloaded it the example is...
