Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi Sir,
We have the " Capacitive sensor low-level library " as below in Nordic SDK.
1. err_code = nrf_drv_csense_init (&csense_config, csense_handler);
2. nrf_drv_csense_channels_enable...
Hi,
I use nRF52840 DK with SoftDevice 140 v.7.0.1 and SDK 16.0.0.
I want to get RSSI information (along with channel index) for BLE extended advertisements.
I enabled...
I am working with a custom hardware device similar to the Thingy91. I am communicating with an external device using COM1 using a binary stream at 38400 N81. (COM0 is assigned...
My design uses an RV-3028 RTC as an external 32 kHz oscillator for the application timer. Do I have to configure the SDK to use an external oscillator instead of a crystal...
I recently updated my multi-protocol (Thread FTD + BLE Peripheral Connectable) to use 'nRF5_SDK_for_Thread_and_Zigbee_3.0.0_d310e71'. I had been previously using 'nRF5_SDK_for_Thread_and_Zigbee_2...
Hi,
I setted up the LIBUARTE on my custom board...
NRF52833,SDK17.0.2,With Softdevice enabled
CODE:
-----------------------------------
NRF_LIBUARTE_ASYNC_DEFINE...
Hi,
I've found an issue while writing data to QSPI flash memory on the nrf52840 DK board with sample application.
The issue is that the data is overwritten to 0x0 address...
I am working on putting my NRF52840 to sleep with the RTC running (System ON WFE, not System Off). According to the datasheet, I should be able to call a soft reset and keep...
Hello, I am having some problems with what i assume is the readback protection. Is it possible to update the firmware of the device without deleting UIRC (serial number among...
I am using nrf52 chipset, I just want to know did anyone tried to run docker container to create ARM image? I am thinking to use Docker container as CI.
Hello
I am using nrf52832 and ble_app_uart of SDK v17.0.
I am sending data to the app every second through the notify function. If I try to disconnect and reconnect Bluetooth...
Hello,
Is the Power Profiler Kit II (PPK2) only usable for nRF product line and custom boards, or can it be use beyond the nRF line of products such as boards not made by...
Hello!
I am currently working on a project with my nRF52832 that is using BLE communication with a android phone. I have tried some of Nordics' examples that use BLE, but...
Hi all,
I have a question concerning the nRF52833.
I'd like to know if there is a safety limit on the amount of reflected power that is reflected by the antenna inside...
Dear Nordic,
I changed the value in the Bootloader to not erase the 4k just before the bootlader.
NRF_DFU_APP_DATA_AREA_SIZE 4096
In the app I changed the rom size...
