Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am now pulling my hair out with these drivers ... I'm trying to do what I think is the right thing and use the new nrfx drivers, but it's really not easy.
So this started...
Hi, I am using Zephyr's BLE for transmission In the peripheral, I record the time when I send the notify to cental (start time) Then when I received the central write_without_response...
Hello,
I have a peripheral that is connected to nRF52832 using I2C, in which I want to send some file to its memory. However, for sending this file, I need to stream it...
I have an existing BLE project that works as a mesh but does not use nRF SDK for Mesh. Using sdk 17.0.2, s140 7.2.0 on nrf52840s and visualGDB.
It works well for most clients...
Hi, I want to evaluate my anttena design. I have tuned it. With the dongle I can scan the air for radio signals, I see then my Wifi and I see the BLE radio of my board. Now...
Hello Nordic Community,
In order to measure battery voltage, I am using ADC with the code implemented as below:
In this, there is a while loop used to wait for ADC to...
We are developing an IoT device communicating via LTE to AWS IoT Hub using authentication by client certificate. For that, we are powering on the modem, do a mqtt_connect...
I am on nrfConnect v3.6 trying to build an SPI test using the command line (west)
I get this error:
```
error: SPI_3_NRF_SPIM (defined at drivers/spi/Kconfig.nrfx:133...
Hello,
I have imported a blinky project in SEGGER. I have added one user library to the project. Now I want to use this library in the main. c.
But I am not able to include...
So what I understand from the lesson over here is that we have couple of timers available to us and each timer comprise of multiple compare/capture register which can be used...
I need to implement using OTA to upgrade the thread.I followed Thread Tutorial: Practical guide for device upgrade OTA provided to complete the upgrade process,but it didn...
Dear Member,
I want to calculate distance I have traveled,
I saw variables as
#define WHEEL_CIRCUMFERENCE 2070 /**< Bike wheel circumference [mm] */
static uint32_t...
Hi,
I've followed the instructions to apply the free Nordic license for SES but it doesn't seem to like the MAC address. You can see from the attached images that the MAC...
Hi
My device is a medical device, we are now beginning verification. One of the items on the spec requires verification that 128bit AES is used during post-bond comms with...
Hello,
I have developed a small sensor which consists of MAX30101 HR sensor and nRF52832. For the research purpose I created an app as well which shows the raw data sent...
