Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi
I am evaluating the production of a BLE product and your chip solution looks promising.
In my case the bluetooth will be connected to PC and it should be recognized...
There are a number of issues in ble_advertising that relate to changing the status of advertising in response to events. Specifically the current adv mode is not changed on...
Looking at the schematic diagram of the ISP-1507-AX Test Board….
www.insightsip.com/.../ISP1507_AX_TB_Schematic.pdf
… I can see that there is the possibility to connect...
Hi
I am using ble_app_uart code from ble_peripheral folder and nrf_connect app to receive/send data.
I have interfaced external sensor with UART pins and receiving data...
Hi I am using UART code from nRF5_SDK_16.0.0_98a08e2\examples\peripheral.
I have checked loop back with default UART pins,which are 5,6,7,8.
Now I want to interface some...
Hello,
I am using a nRF52DK (PCA10056). When I connect the board, the J-link drive opens up, but it does not detect on nRF Go Studio, nor is it flashing any code. I am using...
I'm using the USB CDC ACM example to write a message to a com port. I can receive messages fine except there is one problem. I am receiving the characters one character at...
Hi,
Is it possible to use two LPCOMPs simultaneously?
I would like to use analog channel 6 and 5 and if I register a RESULT Above on channel 6 it should start a software...
Good day to all
I would like to get a little more information about the function:
added in softdevice version 7.0.1.
Starting the radio in connection mode is shown...
Hi,
I'm experiencing some UART issues on nRF52832 where it seems like the peripheral is not correctly reset when doing a soft reset. After a soft reset I expect that the...
Hi,
I am using nrf25840 Dongle as NCP with Linux machine. I have used NCP example hex from " nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac\examples\thread\ncp\usb_bootloader...
How to achieve the lowest power consumption while "sleeping" but still being able to awake from an internal timer ?
For the timer I'm using the Ticker class from mbed.....
Hi,
I am a Embedded System Engineer working in a Medical device company in Ireland. I have a ublox Modem(Nina-B111), which has a nRF5xxx module embedded into it. The modem...
Dear Sir .
I have on my custom board 2 spi , spi1 and spi3.
&spi3 { status = "okay"; compatible = "nordic,nrf-spim"; sck-pin = <31>; mosi-pin = <9>; miso-pin = <30>;...
Hi,
Now I use Nrf52811 to develop a product. I use the 125k long range radio + 4dB mode.
I read through its specifications and found no corresponding...