My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
Hello,
I'm looking for some general guidance on the following application:
1 nRF52840 based gateway to cloud, on power supply
a few hundred nRF52832 sensor nodes,...
We want to use app_timer_create/app_timer_start to create a periodic timer, but noticed that there were a few seconds missing. After printing out each tick, we see that there...
I can't open my tickets since it's changed into private ticket by your engineer.How can I do?
My ticket' name is"about service change can't receive BLE_GATTS_EVT_WRITE"...
Hi,
I will work with nRF51822. I installed all software tools and I connect target device with debugger.
Should I connect nRF51822 with power like battery (because I will...
I used SES and wrote a printf message at main entrance: when I run in nRF Connect I can see the message that I wrote just after I press the RESET button (OK). Still, as I...
Hi,
What is the GPIO pin state during reset, and during startup ? I have seen that it is a high impedance floating input. How much is the value of this impedance? Can I...
Hello,
We're beginning FCC certification next week and I've been creating radio test and DTM versions of firmware that can run on our hardware for the lab. Everything looks...
I am using the nRF51422 for BLE data. My antenna matching network is this:
However, compared to the DK I am getting lower gain (DK gives -50, my PCB gives -64). I have...
Hi,
I want to load both "SPM" and "http_update_ota" code separately to the nRF9160.
For that as suggested in " http://developer.nordicsemi.com/nRF_Connect_SDK/doc/0.4...
I've been trying to configure a second UART for use on the nRF9160 DK. However, I'm having some issues getting anything to send over the UART. I feel like I'm missing something...
Hi,
I use the nrfx_rtc_tick_enable() function to enable tick interrupts for the RTC.
I have a statemachine that in some states disable the interrupt and sometime enables...
Hi everyone !
I want to use serial communication with my ble project. So i tried to implement "/example/peripheral/serial " project into my ble project. I encountered too...
im using Feather EVM. im using the app_ble_uart . after i added SPI to the project i dont get any errors but the code does not run (goes to main) and when i press run it goes...
With an Objective to test mulitple DUTs that provides BLE4.2 data, We are in process of procuring the nRF52840 Dongle.
I would like to understand if i will be able to do...
