Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I need to collect data from 2 ADC channels. Ultimately, the data is to be sent to a table of 1000 samples (500 per channel). Samplerate can be 2KHz - 8kHz. When the table...
I am planning to use clock 16Mhz. I went through examples and found nrfx_spim to be using this option
But nowhere in the code I could pinpoint exactly how the clock itself...
Hi,
I am trying to implement LESC Security Mode 1 Level 4 with a peripheral ble_app_hrs on PCA10040 and a central via pc-ble-driver example heart_rate_collector_v6 with...
We have a Mesh app that should be updated via DFU. The problem is that if a device (for whatever reason) restarts in the middle of DFU or it is powered up later (i.e. not...
I want two STM32 timers synchronization via BLE . Used two nRF52832DKs download the timersync demo : https://github.com/nordic-auko/nRF5-ble-timesync-demo ,
the nRF52832DKs...
Hello
I am having 3 nRF52832 devices and I have to pair any two of them with each other and not with the third one.The third device or any other device should not get...
SDK Mesh 3.1
I was looking at the provisioner example, and noticed that in the function prov_helper_device_handles_load() there is:
But when i look at dsm_subnet_get_all...
Hello all!
I'm having a bit of trouble with complete communication between an nrf51 DK running the micro esb wireless uart example and an nrf24L01+ which is running TMRh20...
Hi!
I am evaluating BLE UART Demo with longe range (BLE_GAP_PHY_CODED).
Max. data throughput (using different parameters for ATT_MTU size and connection inverval) seems...
Hello,
I am designing a wearable using the nRF52810 chip and would like to ask if there are any recommended touchscreens to be used? My main concerns are
SPI bus (at...
GCC linker is capable to generate elf file with a given value for UICR->APPROTECT register with a simple script:
This feature allows generating "always protected firmware...
i'm using this dongle USB840F based on nRF52480.
i'm using usbd_ble_uart_freertos (SDK 15.2) example, the usb port is detected and i can read from it , but it doesn't advertise...
Hello
I'm surprised to see this kind of power profile when the device is in advertising mode.
The 3 TX steps for the 3 canals of advertising haven't got the same max...
Good day,
I wish to adapt the Eddystone Beacon example for nRF51822 with S130 in e.g.:
..\nRF5_SDK_12.3.0\examples\ble_peripheral\ble_app_beacon\pca10028\s130\armgcc ...
In my application, the nRF52840 dongle is hard-wired via UART port pins to the UART interface of a Wi-Fi gateway host board. I need the nRF52 application to restart when it...
