Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hello
I am using Android and BLE communication with nRF52832 (BLENano2) now.
I am using SDK 15.0.0 with keil uversion.
Central is Android and peripheral is nRF52832...
Hello
I am using Android and BLE communication with nRF52832 (BLENano2) now.
I am using SDK 15.0.0 with keil uversion.
Central is Android and peripheral is nRF52832...
Hello
I am using Android and BLE communication with nRF52832 (BLENano2) now.
I am using SDK 15.0.0 with keil uversion.
Central is Android and peripheral is nRF52832...
Hello,
I use the LAIRD module BL652 with an nRF52832 with the SoftDevice 14.0.0 (old version…).
The application use the BLE with the SoftDevice.
We have mesured the...
Hello,
Here i are using nRF52832 ,softdevice S132 and mesh sdk v3.0.0
For my Application,i need to go with DFU.so i merged my application into the example code of DFU...
Hello,
Does anyone know if the FreeRTOS port that's distributed with the nRF5_SDK_14.2.0 is intended to support nRF52810 chips (which have no hardware FPU)? I started working...
SDK 14.2 keil5
I want to run freertos with nrf52810.but I did not find any example .
Is there anyone have tried this?
I downloaded nrf52832 code(ble_app_hrs_freertos...
Hello All,
I have looked around for answers to my specific issue, however I did not seem to find one that aided me enough to fix my issue.
I have created a BLE profile...
Hello,
SDK 15.2, SD 6.1.0 with PCA10056 1.0.0, 2018.20. nRF Connect App v4.22.3. Pixel XL.
I'm running into an issue with my application where the phone disconnects after...
Using: Linux (Ubuntu 18.04), gcc/Eclipse, nrf52840, v15.3.0 SDK, SD 6.1.1
It has been a real bear of time using the SDFU in the newest version of the SDK. There were a lot...
Dear support,
Our team is considered doing their own smart watch, so i found that nRF52 chip is a nice solution. Just before we start, i would like to do some basic questions...
When we ported our FreeRTOS based project to SDK 15.3 from 15.2, we noticed a big jump in the CPU Usage. It turned out that the issue was in SDK 15.3's freertos port_cmsis_systick...
Hi nordic,
I send multiple bytes but always only receive packets of length = 1. For example in the picture, I sent 2 bytes 0x68, 0x69 ('DE') but only received the first...
